- 您現在的位置：買賣IC網 > PDF目錄375864 > FMS7401LVN14 (FAIRCHILD SEMICONDUCTOR CORP) Digital Power Controller PDF資料下載
參數資料
| 型號： | FMS7401LVN14 |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Digital Power Controller |
| 中文描述： | 8-BIT, EEPROM, 2.04 MHz, MICROCONTROLLER, PDIP14 |
| 封裝： | PLASTIC, DIP-14 |
| 文件頁數： | 10/80頁 |
| 文件大?。?/td> | 1535K |
| 代理商： | FMS7401LVN14 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
FMS7401/7401L
PRODUCT SPECIFICATION
10
REV. 1.0.2 6/23/04
2
Clock Circuit
The FMS7401/7401L may be clocked using its internal oscillator circuit or using an external digital clock signal. The desired
clock source is selectable by the CMODE bit of the Initialization Register 1.
updated and the desired clock source (also called the device reference clock or F
are defaulted from the factory to use the internal oscillator as their main system instruction clock source. After power-up, the
internal oscillator runs continuously unless entering Halt Mode or using an external clock source.
1
During the reset sequence, the CMODE bit is
) takes control of the device. All devices
RCLK1
Table 2. CMODE Bit Definition
The internal oscillator signal is factory trimmed to yield the F
of the datasheet. If the external digital clock is selected, the input signal must have a 50/50 duty cycle, can range from DC to
the F
OSC
, and must be available upon power-up. When the device is driven using an external clock source, the clock input to the
device should be provided through the AIN3/G1 input.
OSC
frequency as specified in the
Electrical Characteristics
section
Once the source of F
the Programmable Comparator circuit, and is divided-by-2 to be used as the main system instruction clock (F
(see
Figure 3
and
Figure 4
).
RCLK1
is selected, the clock is then used as the reference clock for the PLL, the clock to the digital filter in
ICLK
) of the device
2.1
The FMS7401/7401L has an internal digital clock multiplier (PLL) that steps-up the F
tor of 32. The multiplied PLL output is then divided by a factor of 1, 2, 4, and 8 in order to generate its programmable output
frequencies that may be used as the main system instruction clock or by the PWM Timer 1 circuit. The PLL provides the ability
to run the PWM Timer 1 circuit at a frequency as high as 64MHz while the rest of the device operates at a much slower fre-
quency keeping the total current consumption low.
PLL
RCLK1
frequency by a multiplication fac-
The reference clock of the PLL is defined by the F
signal. In order to yield the proper output frequencies offered by the PLL, F
fied in the
Electrical Characteristics
section of the datasheet. In the case that F
the REFBY2 bit in the ADCNTRL2 register
quency of the F
RCLK2
signal. Once the REFBY2 bit is set, the F
grammable Comparator circuit operates at a F
must be supplied at the specified F
OSC
frequency in order to meet the specified F
RCLK2
signal (as shown in
Figure 3
and
Figure 4
) and sourced by the F
must operate at the F
is operating at the upper F
must be set in order to divide the F
RCLK1
signal that drives the PLL and digital filter in the Pro-
/2 frequency. If an external digital clock is sourcing F
frequency of the F
RCLK1
RCLK2
PLL
frequency as speci-
frequency,
RCLK1
OSC
2
3
by 2 to yield the appropriate F
PLL
fre-
RCLK2
RCLK1
RCLK1
, the input signal
signal.
PLL
RCLK2
Table 3. PLL Frequency Selection (F
PLL
/F
OSC
= 2MHz)
The PLL outputs may be used to clock both the PWM Timer 1 circuit and the main system clock. However, the PLL must first
be enabled by setting the PLLEN bit of the PSCALE register.
Once set, the PLL is turned on and begins the locking phase.
Before using any of the PLL outputs, software must wait the T
PLL_LOCK
quency and in phase. The PLLEN bit may not be changed while the PWM Timer 1 circuit is in run mode.
to this bit during this condition will not change its value.
4
to ensure that the PLL is locked into its appropriate fre-
5
Any write attempts
The PWM Timer 1 circuit may be clocked either by the PLL’s F
bit of the PSCALE register
selects between the PLL’s F
not be set if the PLL is not enabled (PLLEN=0) or changed while the PWM Timer 1 circuit is in run mode.
5
Any write attempts
to this bit during these conditions will not change its value.
PWMCLK
output or by the main system clock (F
PWMCLK
output (if FSEL=1) or F
ICLK
(if FSEL=0). The FSEL bit may
ICLK
). The FSEL
4
CMODE
F
RCLK1
Clock Source
0
Internal Oscillator (@ F
OSC
)
1
External digital clock (G1/AIN3)
FS[1:0]
F
RCLK2
F
ICLK
(FMODE = 0)
F
ICLK
(FMODE = 1)
F
PWMCLK
0
0
2 MHz
1 MHz
8 MHz
8 MHz
0
1
2 MHz
1 MHz
8 MHz
16 MHz
1
0
2 MHz
1 MHz
8 MHz
32 MHz
1
1
2 MHz
1 MHz
8 MHz
64 MHz
相關PDF資料 |
PDF描述 |
|---|---|
| FMS7G10US60S | SWTCH ROLLER SPDT 20A SCRW TERM |
| FMS7G10US60 | SWTCH ROLLER SPDT 20A SOLD TERM |
| FMS7G15US60S | SWTCH LEVER SPDT 20A SCREW TERM |
| FMS7G15US60 | SWTCH ROLLER SPDT 20A SCRW TERM |
| FMS7G20US60S | Compact & Complex Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FMS7401LVN14_Q | 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| FMS75X6 | 功能描述:MAGENTIC STRIP .75" X 6' RoHS:否 類別:線纜，導線 - 管理 >> 線槽，走線系統 - 附件 系列:- 標準包裝:1 系列:PANDUCT® 附件類型:蓋 - 線管 適用于相關產品:Panduit 導管 H 型 高度:- 寬:4"（101.6mm） 長度:36.0"（914.4mm） 顏色:黑 其它名稱:298-HC4BL36 |
| FMS7857MTD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver |
| FMS7857MTDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver |
| FMS7950KWC | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。