參數資料
型號： FMS7401LVN14
廠商： FAIRCHILD SEMICONDUCTOR CORP
元件分類： 微控制器/微處理器
英文描述： Digital Power Controller
中文描述： 8-BIT, EEPROM, 2.04 MHz, MICROCONTROLLER, PDIP14
封裝： PLASTIC, DIP-14
文件頁數： 50/80頁
文件大小： 1535K
代理商： FMS7401LVN14
PRODUCT SPECIFICATION
FMS7401/7401L
REV. 1.0.2 6/23/04
50
10.1.6 Interrupt Handling
When an interrupt is recognized, the current instruction completes its execution. The return address (the current value in the
program counter, PC) is pushed onto the stack, the global interrupt (G) mask of the status register (SR) is cleared, and execu-
tion continues at the address specified by the respective interrupt vector (see
Table 30
). This process takes five instruction
cycles to complete. The interrupt vector contains the address of the software’s interrupt service routine (ISR). Initially, the ISR
may save (if necessary) the status register’s contents. Software, however, cannot restore SR using the traditional microcontrol-
ler methods. Just before ending the ISR, software may restore the contents of SR by using only the special inherent instructions
(e.g. SC, RC and LDC) or specially defined software routines since all SR bits except for G are read only when using direct,
indirect, or indexed instructions (e.g. LD , ST, RBIT or SBIT). Upon exiting the ISR, software must clear the appropriate
triggering pending flag and execute a return-from-interrupt (RETI) instruction. The RETI instruction pulls the saved return
address off the stack in reverse order restoring PC and setting G of SR to one. Instruction execution resumes at the restored the
program counter address.
The microcontroller core is capable of supporting five interrupts. Four are maskable through G of the SR and the fifth (software
interrupt) is not inhibited by G (see
Figure 18
). The execution of the INTR instruction generates a software interrupt. Once the
INTR instruction is executed, the microcontroller core will interrupt whether G is set or not. The INTR interrupt is executed in
the same manner as the other maskable interrupts where PC is stacked and G is cleared. This means, if G was enabled prior to
the software interrupt the RETI instruction must be used to return from interrupt in order to restore G to one. However, if G
was not enabled prior to the software interrupt the RET instruction must be used.
In the case of simultaneous multiple interrupts, the microcontroller core prioritizes the interrupts. See
Table 23
for the interrupt
service priority sequence.
Figure 18. Basic Interrupt Structure
G
INTR
PWM T1
T0
MIW
Interrupt
Pending
Flags
Interrupt Enable Bits
Global Interrupt
Enable
Interrupt
I
ADC
T1EN
T0INT
EN
WKINT
EN
AINT
EN
T1PND
T0PND
WKPND
APND
相關PDF資料
PDF描述
FMS7G10US60S SWTCH ROLLER SPDT 20A SCRW TERM
FMS7G10US60 SWTCH ROLLER SPDT 20A SOLD TERM
FMS7G15US60S SWTCH LEVER SPDT 20A SCREW TERM
FMS7G15US60 SWTCH ROLLER SPDT 20A SCRW TERM
FMS7G20US60S Compact & Complex Module
相關代理商/技術參數
參數描述
FMS7401LVN14_Q 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
FMS75X6 功能描述:MAGENTIC STRIP .75" X 6' RoHS:否 類別:線纜，導線 - 管理 >> 線槽，走線系統 - 附件 系列:- 標準包裝:1 系列:PANDUCT® 附件類型:蓋 - 線管 適用于相關產品:Panduit 導管 H 型 高度:- 寬:4"（101.6mm） 長度:36.0"（914.4mm） 顏色:黑 其它名稱:298-HC4BL36
FMS7857MTD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver
FMS7857MTDT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver
FMS7950KWC 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Fairchild Semiconductor Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*