The A/D conversio" />
參數資料
型號： KSZ8863MLL-EVAL
廠商： Micrel Inc
文件頁數： 61/106頁
文件大小： 0K
描述： BOARD EVALUATION FOR KSZ8863MLL
標準包裝： 1
主要目的： 接口，以太網 PHY
嵌入式： 否
已用 IC / 零件： KSZ8863MLL
已供物品： 板
相關產品： 576-3751-ND - IC ETHERNET SWITCH 3PORT 48-LQFP
576-3577-ND - IC ETHERNET SW 3PORT 48-LQFP
其它名稱： 576-3867
PIC16C72 Series
1998 Microchip Technology Inc.
Preliminary
DS39016A-page 57
9.2
Selecting the A/D Conversion Clock
The A/D conversion time per bit is dened as TAD. The
A/D conversion requires 9.5TAD per 8-bit conversion.
The source of the A/D conversion clock is software
selectable. The four possible options for TAD are:
2TOSC
8TOSC
32TOSC
Internal RC oscillator
For correct A/D conversions, the A/D conversion clock
(TAD) must be selected to ensure a minimum TAD time
of 1.6
s.
Table 9-1 shows the resultant TAD times derived from
the device operating frequencies and the A/D clock
source selected.
9.3
Configuring Analog Port Pins
The ADCON1, TRISA, and TRISE registers control the
operation of the A/D port pins. The port pins that are
desired as analog inputs must have their correspond-
ing TRIS bits set (input). If the TRIS bit is cleared (out-
put), the digital output level (VOH or VOL) will be
converted.
The A/D operation is independent of the state of the
CHS2:CHS0 bits and the TRIS bits.
TABLE 9-1
TAD vs. DEVICE OPERATING FREQUENCIES
Note 1: When reading the port register, all pins
congured as analog input channels will
read as cleared (a low level). Pins cong-
ured as digital inputs, will convert an ana-
log input. Analog levels on a digitally
congured input will not affect the conver-
sion accuracy.
Note 2: Analog levels on any pin that is dened as
a digital input (including the AN4:AN0
pins), may cause the input buffer to con-
sume current that is out of the devices
specication.
AD Clock Source (TAD)
Device Frequency
Operation
ADCS1:ADCS0
20 MHz
5 MHz
1.25 MHz
333.33 kHz
2TOSC
00
100 ns(2)
400 ns(2)
1.6
s
6
s
8TOSC
01
400 ns(2)
1.6
s
6.4
s
24
s(3)
32TOSC
10
1.6
s
6.4
s
25.6
s(3)
96
s(3)
RC(5)
11
2 - 6
s(1,4)
2 - 6
s(1,4)
2 - 6
s(1,4)
2 - 6
s(1)
Legend: Shaded cells are outside of recommended range.
Note 1: The RC source has a typical TAD time of 4
s.
2: These values violate the minimum required TAD time.
3: For faster conversion times, the selection of another clock source is recommended.
4: When device frequency is greater than 1 MHz, the RC A/D conversion clock source is recommended for
sleep operation only.
5: For extended voltage devices (LC), please refer to Electrical Specications section.
相關PDF資料
PDF描述
V150B36E150BL CONVERTER MOD DC/DC 36V 150W
50PX47MEFCTA6.3X11 CAP ALUM 47UF 50V 20% RADIAL
IR3084UMTRPBF IC CTLR XPHASE 28-MLPQ
202D296-25-0 BOOT MOLDED
1812R-104J INDUCTOR UNSHIELDED 100UH SMD
相關代理商/技術參數
參數描述
KSZ8863MLLI 功能描述:以太網 IC 3-Port Copper 10/100 Ethernet Switch w/ 1x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863RLL 功能描述:以太網 IC 3-Port Copper 10/100 Ethernet Switch with 1x RMII Interface (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863RLL-EVAL 功能描述:以太網開發工具 3-Port Copper 10/100 Ethernet Switch with 1x RMII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8863RLLI 功能描述:以太網 IC 3-Port Copper 10/100 Ethernet Switch w/ 1x RMII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8864CNXCA 功能描述:Ethernet Controller 10/100 Base-T/TX PHY MII, RMII Interface 64-QFN (8x8) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:控制器 接口:MII，RMII 標準:10/100 Base-T/TX PHY 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:- 工作溫度:0°C ~ 70°C 封裝/外殼:64-VFQFN 裸露焊盤 供應商器件封裝:64-QFN（8x8） 標準包裝:348
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*