SPI/I2C UART with 128-Word FIFOs in WLP MAX3108 19 Maxim Integrated 2x and 4x Ra" />
參數資料
型號： MAX3108EWA+T
廠商： Maxim Integrated Products
文件頁數： 11/56頁
文件大?。?/td> 0K
描述： IC UART
產品培訓模塊： Obsolescence Mitigation Program
標準包裝： 2,500
系列： *
SPI/I2C UART with 128-Word FIFOs in WLP
MAX3108
19
Maxim Integrated
2x and 4x Rate Modes
The MAX3108 offers 2x and 4x rate modes in order to
support higher baud rates than possible with standard
operation using 16x sampling. In these modes, the refer-
ence clock rate only needs to be either 8x or 4x higher
than the baud rate, respectively. In 4x rate mode, each
received bit is only sampled once at the midbit instant
instead of the usual three samples to determine the
logic value of the received bit. This reduces the abil-
ity to detect line noise on the received data in 4x rate
mode. The 2x and 4x rate modes are selectable through
BRGConfig[5:4]. Note that IrDA encoding and decoding
does not operate in 2x and 4x rate modes.
When 2x rate mode is selected, the actual baud rate is
twice the rate programmed into the baud-rate genera-
tor. If 4x rate mode is enabled, the actual baud rate on
the line is quadruple that of the programmed baud rate
(Figure 8).
Multidrop Mode
In multidrop mode, also known as 9-bit mode, the data
word length is 8 bits and a 9th bit is used for distin-
guishing between an address word and a data word.
Multidrop mode is enabled by the MODE2[6]: MultiDrop
bit. The MultiDrop bit takes the place of the parity bit in
the data word structure. Parity checking is disabled and
an interrupt is generated in SpclCharInt[5]: MultiDropInt
when an address (9th bit is 1) is received while in multi-
drop mode.
It is up to the host processor to filter out the data intended
for its address. Alternatively, the auto data-filtering fea-
ture can be used to automatically filter out the data not
intended for the station’s specific 9-bit mode address.
Auto Data Filtering in Multidrop Mode
In multidrop mode, the MAX3108 can be configured
to automatically filter out data that is not meant for its
address. The address is user-definable either by pro-
gramming a register value or a combination of a register
value and GPIO hardware inputs. Use either the entire
XOFF2 register or the XOFF2[7:4] bits in combination
with GPIO_ inputs to define the address.
Enable multidrop mode by setting the MODE2[6]:
MultiDrop bit high and enable auto data filtering by set-
ting the MODE2[4]: SpecialChr bit high.
When using register bits in combination with GPIO_
inputs to define the address, the MSB of the address
is written to the XOFF2[7:4] bits, while the LSBs of
the address are defined by the GPIOs. To enable this
address-definition method along with auto data filter-
ing, set the FlowCtrl[2]: GPIAddr bit high in addition to
the MODE2[4]: SpecialChr and MODE2[6]: MultiDrop
bits. The GPIO_ inputs are automatically read when the
FlowCtrl[2]: GPIAddr bit is set high, and the address
is automatically updated on logic changes to any GPIO
pin.
When using auto data filtering, the MAX3108 checks
each received address against the programmed station
address. When an address is received that matches
the station’s address, received data is stored in the
RxFIFO. When an address is received that does not
match the station’s address, received data is discarded.
Addresses are not stored into the FIFO but an inter-
rupt is still generated in SpclCharInt[5]: MultiDropInt
upon receiving an address. An additional interrupt is
generated in SpclCharInt[3]: XOFF2Int when the station
address is received.
Figure 8. 2x and 4x Baud Rates
FRACTIONAL
RATE
GENERATOR
fREF
BAUD RATE
BRGConfig[5:4]
DIV[LSB]
DIV[MSB]
NOTE: IrDA DOES NOT WORK IN 2x AND 4x MODES.
FRACT
1x, 2x, 4x RATE
MODES
相關PDF資料
PDF描述
MAX3109ETJ+ SEMICONDUCTOR OTHER
MAX310CPE IC VIDEO MULTIPLEXER 8X1 16DIP
MAX3110EENI+G36 IC UART SPI COMPAT 28-DIP
MAX3120CUA+ IC TXRX INFRARED IRDA 8-UMAX
MAX3120EUA IC TXRX 3V IRDA IR 3V 8-UMAX
相關代理商/技術參數
參數描述
MAX3109ETJ+ 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3109ETJ+T 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX310C/D 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX310CPE 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX310CPE+ 功能描述:多路器開關 IC 8:1 Unbuffered RF Video MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*