SPI/I2C UART with 128-Word FIFOs in WLP MAX3108 50 Maxim Integrated Single-Byte " />
參數資料
型號： MAX3108EWA+T
廠商： Maxim Integrated Products
文件頁數： 46/56頁
文件大小： 0K
描述： IC UART
產品培訓模塊： Obsolescence Mitigation Program
標準包裝： 2,500
系列： *
SPI/I2C UART with 128-Word FIFOs in WLP
MAX3108
50
Maxim Integrated
Single-Byte Write
In this operation, the master sends an address and two
data bytes to the slave device (Figure 18). The following
procedure describes the single-byte write operation:
1) The master sends a START condition.
2) The master sends the 7-bit slave address plus a write
bit (low).
3) The addressed slave asserts an ACK on the data line.
4) The master sends the 8-bit register address.
5) The slave asserts an ACK on the data line only if the
address is valid (NACK if not).
6) The master sends 8 data bits.
7) The slave asserts an ACK on the data line.
8) The master generates a STOP condition.
Burst Write
In this operation, the master sends an address and mul-
tiple data bytes to the slave device (Figure 19). The slave
device automatically increments the register address
after each data byte is sent, unless the register being
accessed is 0x00, in which case the register address
remains the same. The following procedure describes
the burst write operation:
1) The master sends a START condition.
2) The master sends the 7-bit slave address plus a write
bit (low).
3) The addressed slave asserts an ACK on the data line.
4) The master sends the 8-bit register address.
5) The slave asserts an ACK on the data line only if the
address is valid (NACK if not).
6) The master sends 8 data bits.
7) The slave asserts an ACK on the data line.
8) Repeat 6 and 7 N-1 times.
9) The master generates a STOP condition.
Figure 18. Write Byte Sequence
Figure 19. Burst Write Sequence
S
P
DEVICE SLAVE ADDRESS - W
A
8 DATA BITS
FROM MASTER TO STAVE
WRITE SINGLE BYTE
FROM SLAVE TO MASTER
A
REGISTER ADDRESS
A
S
DEVICE SLAVE ADDRESS - W
A
8 DATA BITS - 1
BURST WRITE
A
REGISTER ADDRESS
A
8 DATA BITS - N
A
8 DATA BITS - 2
A
FROM MASTER TO STAVE
FROM SLAVE TO MASTER
P
相關PDF資料
PDF描述
MAX3109ETJ+ SEMICONDUCTOR OTHER
MAX310CPE IC VIDEO MULTIPLEXER 8X1 16DIP
MAX3110EENI+G36 IC UART SPI COMPAT 28-DIP
MAX3120CUA+ IC TXRX INFRARED IRDA 8-UMAX
MAX3120EUA IC TXRX 3V IRDA IR 3V 8-UMAX
相關代理商/技術參數
參數描述
MAX3109ETJ+ 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3109ETJ+T 功能描述:UART 接口集成電路 Dual Serial UART with 128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX310C/D 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX310CPE 功能描述:多路器開關 IC RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MAX310CPE+ 功能描述:多路器開關 IC 8:1 Unbuffered RF Video MUX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*