- 您現在的位置：買賣IC網 > PDF目錄45234 > MC68HC58DW (MOTOROLA INC) 1 CHANNEL(S), LOCAL AREA NETWORK CONTROLLER, PDSO28 PDF資料下載
參數資料
| 型號： | MC68HC58DW |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 1 CHANNEL(S), LOCAL AREA NETWORK CONTROLLER, PDSO28 |
| 封裝： | SOIC-28 |
| 文件頁數： | 20/102頁 |
| 文件大?。?/td> | 700K |
| 代理商： | MC68HC58DW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MOTOROLA
SIGNAL AND PIN DESCRIPTIONS
MC68HC58
2-8
TECHNICAL DATA
2.2.1.3 INT — DLC Interrupt Request
This pin is used to output an open drain active-low interrupt request signal to the MCU.
The signal is fully compatible with M68HC05, M68HC11, M68HC16, and M68300 in-
terrupt request inputs. INT must have an external pull-up resistor.
2.2.1.4 LITO — Logic In Transceiver Out
This pin is an external tap on the internal receive signal sent from the transceiver to
the control logic. It is used for testing only, and must be left unconnected for normal
operation.
2.2.1.5 LOAD — External Bus Load
This pin provides an internal ground connection for the SAE J1850 multiplex bus load
resistor. If DLC analog ground is lost, LOAD goes to a high-impedance state.
2.2.1.6 LOTI — Logic Out Transceiver In
This pin is an external tap on the internal transmit signal sent from the control logic to
the transceiver. It is used for testing only, and must be left unconnected for normal op-
eration.
2.2.1.7 OSC1, OSC2 — External Oscillator
The DLC can operate with either an external clock signal or an external ceramic res-
onator. These pins support connection of both types of clock. If an external clock
source is used, the signal is input via OSC1, and OSC2 is left floating. If a resonator
is used, it is connected between OSC1 and OSC2.
2.2.1.8 PRLMD —Parallel Mode
This pin is used to select the desired MCU interface mode. When this pin is pulled
down from VDD, the serial mode is selected.
2.2.1.9 PSEN — Power Supply Enable
This pin provides an external VBATT source when the DLC is active. It assumes high-
impedance state when the DLC is in standby mode.
2.2.1.10 RST — DLC Reset
This pin is used to input an active-low system reset signal. RST must have an external
pull-up resistor.
2.2.1.11 REXT — External Bias Resistor
This pin connects an external bias resistor to the transceiver. The resistor value deter-
mines the waveform of the transmitted BUS signal.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC68T1P | 1 TIMER(S), REAL TIME CLOCK, PDIP16 |
| MC68HC705B16NVFNR2 | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC52 |
| MC68HC705B16NCFNR2 | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC52 |
| MC68HC705B16VFNR2 | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC52 |
| MC68HC705B5VFNR2 | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC68T1P | 制造商:Motorola Inc 功能描述: |
| MC68HC705B16CFN | 制造商:Motorola Inc 功能描述: |
| MC68HC705B16FN | 制造商:Rochester Electronics LLC 功能描述: |
| MC68HC705B16NB | 制造商:Rochester Electronics LLC 功能描述: |
| MC68HC705B16NCB | 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。