參數資料
型號： MPC5200
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Hardware Specifications
中文描述： 硬件規格
文件頁數： 12/80頁
文件大?。?/td> 790K
代理商： MPC5200
MPC5200 Data Sheet, Rev. 4
Electrical and Thermal Characteristics
Freescale Semiconductor
12
Historically, the thermal resistance has frequently been expressed as the sum of a junction to case thermal
resistance and a case to ambient thermal resistance:
R
θ
JA
= R
θ
JC
+R
θ
CA
Eqn. 2
where:
R
θ
JA
= junction to ambient thermal resistance (°C/W)
R
θ
JC
= junction to case thermal resistance (°C/W)
R
θ
CA
= case to ambient thermal resistance (°C/W)
R
θ
JC
is device related and cannot be influenced by the user. The user controls the thermal environment to
change the case to ambient thermal resistance, R
θ
CA
. For instance, the user can change the air flow around
the device, add a heat sink, change the mounting arrangement on printed circuit board, or change the
thermal dissipation on the printed circuit board surrounding the device. This description is most useful for
ceramic packages with heat sinks where some 90% of the heat flow is through the case to the heat sink to
ambient. For most packages, a better model is required.
A more accurate thermal model can be constructed from the junction to board thermal resistance and the
junction to case thermal resistance
1-3
. The junction to case covers the situation where a heat sink will be
used or where a substantial amount of heat is dissipated from the top of the package. The junction to board
thermal resistance describes the thermal performance when most of the heat is conducted to the printed
circuit board. This model can be used for either hand estimations or for a computational fluid dynamics
(CFD) thermal model.
To determine the junction temperature of the device in the application after prototypes are available, the
Thermal Characterization Parameter (
Ψ
JT
) can be used to determine the junction temperature with a
measurement of the temperature at the top center of the package case using the following equation:
T
J
= T
T
+(
Ψ
JT
×
P
D
)
Eqn. 3
where:
T
T
= thermocouple temperature on top of package (°C)
Ψ
JT
= thermal characterization parameter (°C/W)
P
D
= power dissipation in package (W)
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned, so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over approximately one mm of wire extending from the junction. The
thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling
effects of the thermocouple wire.
3.2
Oscillator and PLL Electrical Characteristics
The MPC5200 System requires a system-level clock input SYS_XTAL. This clock input may be driven
directly from an external oscillator or with a crystal using the internal oscillator.
相關PDF資料
PDF描述
MPC5534 Microcontroller
MPC7447A PowerPC microprocessor
MPC7447ANXPNS PowerPC microprocessor
MPC7455 RISC Microprocessor Hardware Specifications
MPC7457 RISC Microprocessor Hardware Specifications
相關代理商/技術參數
參數描述
MPC5200B 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SDRAM/DDR Memory Controller
MPC5200B_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SDRAM / DDR Memory Controller
MPC5200B_10 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SDRAM/DDR Memory Controller
MPC5200BDS 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Data
MPC5200BV400 功能描述:微處理器 - MPU 400MHz 760MIPS RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*