參數資料
型號： MSC7119VM1200
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 數字信號處理
英文描述： 0-BIT, 300 MHz, OTHER DSP, PBGA400
封裝： LEAD FREE, MAPBGA-400
文件頁數： 20/60頁
文件大?。?/td> 1138K
代理商： MSC7119VM1200
Electrical Characteristics
MSC7119 Data Sheet, Rev. 8
Freescale Semiconductor
27
Figure 6 shows the DDR DRAM output timing diagram.
209
Dn/DQMn output setup with respect to DQSn3
tDDKHDS,
tDDKLDS
0.25
× tCK – 750
—
ps
210
Dn/DQMn output hold with respect to DQSn3
tDDKHDX,
tDDKLDX
0.25
× tCK – 750
—
ps
211
DQSn preamble start4
tDDKHMP
–0.25
× tCK
—ps
212
DQSn epilogue end5
tDDKHME
–600
600
ps
Notes:
1.
All CK/CK referenced measurements are made from the crossing of the two signals ±0.1 V.
2.
tDDKHMH can be modified through the TCFG2[WRDD] DQSS override bits. The DRAM requires that the first write data strobe
arrives 75–125% of a DRAM cycle after the write command is issued. Any skew between DQSn and CK must be considered
when trying to achieve this 75%–125% goal. The TCFG2[WRDD] bits can be used to shift DQSn by 1/4 DRAM cycle
increments. The skew in this case refers to an internal skew existing at the signal connections. By default, the CK/CK crossing
occurs in the middle of the control signal (An/RAS/CAS/WE/CKE) tenure. Setting TCFG2[ACSM] bit shifts the control signal
assertion 1/2 DRAM cycle earlier than the default timing. This means that the signal is asserted no earlier than 600 ps before
the CK/CK crossing and no later than 600 ps after the crossing time; the device uses 1200 ps of the skew budget (the interval
from –600 to +600 ps). Timing is verified by referencing the falling edge of CK. See Chapter 10 of the MSC711x Reference
Manual for details.
3.
Determined by maximum possible skew between a data strobe (DQS) and any corresponding bit of data. The data strobe
should be centered inside of the data eye.
4.
Please note that this spec is in reference to the DQSn first rising edge. It could also be referenced from CK(r), but due to
programmable delay of the write strobes (TCFG2[WRDD]), there pre-amble may be extended for a full DRAM cycle. For this
reason, we reference from DQSn.
5.
All outputs are referenced to the rising edge of CK. Note that this is essentially the CK/DQSn skew in spec 208. In addition
there is no real “maximum” time for the epilogue end. JEDEC does not require this is as a device limitation, but simply for the
chip to guarantee fast enough write-to-read turn-around times. This is already guaranteed by the memory controller operation.
Figure 6. DDR DRAM Output Timing Diagram
Table 18. DDR DRAM Output AC Timing (continued)
No.
Parameter
Symbol
Min
Max
Unit
An
Dn
DQSn
CK
D1
D0
Write A0
NOOP
RAS
CAS
WE
CKE
200
208
209
212
210
211
206
204
207
205
DQMn
相關PDF資料
PDF描述
MSC8102M4000 32-BIT, 75 MHz, OTHER DSP, CBGA431
MSC8122TVT6400 32-BIT, 400 MHz, OTHER DSP, PBGA431
MSC8122TVT4800V 32-BIT, 300 MHz, OTHER DSP, PBGA431
MSC8122MP8000 32-BIT, 500 MHz, OTHER DSP, PBGA431
MSC8144ETVT800B 133 MHz, OTHER DSP, PBGA783
相關代理商/技術參數
參數描述
MSC711XADS 功能描述:開發板和工具包 - 其他處理器 DEV SYS FOR FSL 711X DEV RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
MSC711XEVM 功能描述:開發板和工具包 - 其他處理器 EVAL KIT W/FULL LIC CW RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
MSC711XEVMT 功能描述:KIT EVAL W/FULL LIC CW RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:* 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
MSC7121VRF 制造商:Freescale Semiconductor 功能描述:GPON UMC 140 MHZ - Trays
MSC7128 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 x 7-Dot Character x 16-Digit Display Controller/Driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*