- 您現在的位置：買賣IC網 > PDF目錄45388 > MSC7119VM1200 (FREESCALE SEMICONDUCTOR INC) 0-BIT, 300 MHz, OTHER DSP, PBGA400 PDF資料下載
參數資料
| 型號： | MSC7119VM1200 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | 0-BIT, 300 MHz, OTHER DSP, PBGA400 |
| 封裝： | LEAD FREE, MAPBGA-400 |
| 文件頁數： | 53/60頁 |
| 文件大?。?/td> | 1138K |
| 代理商： | MSC7119VM1200 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
Ordering Information
MSC7119 Data Sheet, Rev. 8
Freescale Semiconductor
57
3.6
Connectivity Guidelines
This section summarizes the connections and special conditions, such as pull-up or pull-down resistors, for the MSC7119
device. Following are guidelines for signal groups and configuration settings:
Clock and reset signals.
— SWTE is used to configure the MSC7119 device and is sampled on the deassertion of PORESET, so it should be
tied to VDDC or GND either directly or through pull-up or pull-down resistors until PORESET is deasserted. After
PORESET
, this signal can be left floating.
— BM[0–1] configure the MSC7119 device and are sampled until PORESET is deasserted, so they should be tied to
VDDIO or GND either directly or through pull-up or pull-down resistors.
— HRESET should be pulled up.
Interrupt signals. When used, IRQ pins must be pulled up.
HDI16 signals.
— When they are configured for open-drain, the HREQ/HREQ or HTRQ/HTRQ signals require a pull-up resistor.
However, these pins are also sampled at power-on reset to determine the HDI16 boot mode and may need to be
pulled down. When these pins must be pulled down on reset and pulled up otherwise, a buffer can be used with
the HRESET signal as the enable.
— When the device boots through the HDI16, the HDDS, HDSP and H8BIT pins should be pulled up or down,
depending on the required boot mode settings.
Ethernet MAC/TDM2 signals. The MDIO signal requires an external pull-up resistor.
I2C signals. The SCL and SDA signals, when programmed for I2C, requires an external pull-up resistor.
General-purpose I/O (GPIO) signals. An unused GPIO pin can be disconnected. After boot, program it as an output
pin.
Other signals.
—The TEST0 pin must be connected to ground.
—The TPSEL pin should be pulled up to enable debug access via the EOnCE port and pulled down for boundary
scan.
— Pins labelled NO CONNECT (NC) must not be connected.
— When a 16-pin double data rate (DDR) interface is used, the 16 unused data pins should be no connects (floating)
if the used lines are terminated.
— Do not connect DBREQ to DONE (as you would for the MSC8101 device). Connect DONE to one of the EVNT
pins, and DBREQ to HRRQ.
4
Ordering Information
Consult a Freescale Semiconductor sales office or authorized distributor to determine product availability and place an order.
Part
Supply Voltage
Package Type
Pin
Count
Core
Frequency
(MHz)
Solder Spheres
Order Number
MSC7119
1.2 V core
2.5 V memory
3.3 V I/O
Molded Array Process-Ball Grid
Array (MAP-BGA)
400
300
Lead-free
MSC7119VM1200
Lead-bearing
MSC7119VF1200
相關PDF資料 |
PDF描述 |
|---|---|
| MSC8102M4000 | 32-BIT, 75 MHz, OTHER DSP, CBGA431 |
| MSC8122TVT6400 | 32-BIT, 400 MHz, OTHER DSP, PBGA431 |
| MSC8122TVT4800V | 32-BIT, 300 MHz, OTHER DSP, PBGA431 |
| MSC8122MP8000 | 32-BIT, 500 MHz, OTHER DSP, PBGA431 |
| MSC8144ETVT800B | 133 MHz, OTHER DSP, PBGA783 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSC711XADS | 功能描述:開發板和工具包 - 其他處理器 DEV SYS FOR FSL 711X DEV RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| MSC711XEVM | 功能描述:開發板和工具包 - 其他處理器 EVAL KIT W/FULL LIC CW RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| MSC711XEVMT | 功能描述:KIT EVAL W/FULL LIC CW RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:* 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| MSC7121VRF | 制造商:Freescale Semiconductor 功能描述:GPON UMC 140 MHZ - Trays |
| MSC7128 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 x 7-Dot Character x 16-Digit Display Controller/Driver |
發布緊急采購，3分鐘左右您將得到回復。