Refer to the memory controller" />
參數資料
型號： MSC8101VT1375F
廠商： Freescale Semiconductor
文件頁數： 14/104頁
文件大小： 0K
描述： IC DSP 16BIT 250MHZ 332-FCPBGA
標準包裝： 90
系列： StarCore
類型： SC140 內核
接口： 通信處理器模塊（CPM）
時鐘速率： 275MHz
非易失內存： 外部
芯片上RAM： 512kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.60V
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 332-BFBGA，F(xiàn)CPBGA
供應商設備封裝： 332-FCBGA（17x17）
包裝： 托盤
Memory Controller Signals
MSC8101 Technical Data, Rev. 19
Freescale Semiconductor
1-13
1.5 Memory Controller Signals
Refer to the memory controller chapter in the MSC8101 Reference Manual (MSC8101RM/D) for detailed
information about configuring these signals.
IRQ7
INT_OUT
Input
Output
Interrupt Request 71
One of eight external lines that can request a service routine, via the internal interrupt controller,
from the SC140 core.
Interrupt Output1
Driven from the MSC8101 internal interrupt controller. Assertion of this output indicates that an
unmasked interrupt is pending in the MSC8101 internal interrupt controller.
Notes:
1.
See the SIU chapter in the MSC8101 Reference Manual for details on how to configure these pins.
2.
When used as the bus control arbiter for the system bus, the MSC8101 can support up to three external bus masters. Each
master uses its own set of Bus Request, Bus Grant, and Data Bus Grant signals (BR/BG/DBG,
EXT_BR2/EXT_BG2/EXT_DBG2, and EXT_BR3/EXT_BG3/EXT_DBG3). Each of these signal sets must be configured to
indicate whether the external master is or is not a MSC8101 master device. See the Bus Configuration Register (BCR)
description in the SIU chapter in the MSC8101 Reference Manual for details on how to configure these pins. The second and
third set of pins is defined by EXT_xxx to indicate that they can only be used with external master devices. The first set of pins
(BR/BG/DBG) have a dual function. When the MSC8101 is not the bus arbiter, these signals (BR/BG/DBG) are used by the
MSC8101 to obtain master control of the bus.
3.
See the host interface (HDI16) chapter in the MSC8101 Reference Manual for details on how to configure these pins.
Table 1-6.
Memory Controller Signals
Signal
Data Flow
Description
CS[0–7]
Output
Chip Select
Enable specific memory devices or peripherals connected to MSC8101 buses.
BCTL1
Output
Buffer Control 1
Controls buffers on the data bus. Usually used with BCTL0. The exact function of this pin is defined
by the value of SIUMCR[BCTLC]. See the System Interface Unit (SIU) chapter in the MSC8101
Reference Manual for details.
BADDR[27–28]
Output
Burst Address 27–28
Two of five outputs of the memory controller. These pins connect directly to memory devices
controlled by the MSC8101 memory controller.
ALE
Output
Address Latch Enable
Controls the external address latch used in external master bus configuration.
BCTL0
Output
Buffer Control 0
Controls buffers on the data bus. The exact function of this pin is defined by the value of
SIUMCR[BCTLC]. See the System Interface Unit (SIU) chapter in the MSC8101 Reference Manual
for details.
PWE[0–7]
PSDDQM[0–7]
PBS[0–7]
Output
Bus Write Enable
Outputs of the bus General-Purpose Chip-select Machine (GPCM). These pins select byte lanes for
write operations.
Bus SDRAM DQM
Outputs of the SDRAM control machine. These pins select specific byte lanes of SDRAM devices.
Bus UPM Byte Select
Outputs of the User-Programmable Machine (UPM) in the memory controller. These pins select
specific byte lanes during memory operations. The timing of these pins is programmed in the UPM.
The actual driven value depends on the address and size of the transaction and the port size of the
accessed device.
Table 1-5.
System Bus, HDI16, and Interrupt Signals (Continued)
Signal
Data Flow
Description
相關PDF資料
PDF描述
EBC10DRXS CONN EDGECARD 20POS DIP .100 SLD
TACA107M004RTA CAP TANT 100UF 4V 20% 1206
HCC07DRXI CONN EDGECARD 14POS DIP .100 SLD
FMC13DRAH CONN EDGECARD 26POS R/A .100 SLD
EMM44DRXS CONN EDGECARD 88POS DIP .156 SLD
相關代理商/技術參數
參數描述
MSC8101VT1500F 功能描述:IC DSP 16BIT 250MHZ 332-FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
MSC8102 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core 16-Bit Digital Signal Processor
MSC81020 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS
MSC8102M4000 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core 16-Bit Digital Signal Processor
MSC8102M4400 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core 16-Bit Digital Signal Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*