參數資料
型號： MT9074AL
廠商： Mitel Networks Corporation
英文描述： T1/E1/J1 Single Chip Transceiver
中文描述： T1/E1/J1收發單芯片收發器
文件頁數： 18/122頁
文件大小： 372K
代理商： MT9074AL
MT9074
Advance Information
18
position one of the four FASs of the following
submultiframe before it is transmitted (see Table 12).
The submultiframe is then transmitted and, at the far
end, the same process occurs. That is, a CRC-4
remainder
is
generated
submultiframe. These bits are compared with the bits
received in position one of the four FASs of the next
received submultiframe. This process takes place in
both directions of transmission.
for
each
received
When more than 914 CRC-4 errors (out of a possible
1000) are counted in a one second interval, the
framing algorithm will force a search for a new basic
frame alignment. See Frame Algorithm section for
more details.
The result of the comparison of the received CRC-4
remainder with the locally generated remainder will
be transported to the far end by the E-bits.
Therefore, if E1 = 0, a CRC-4 error was discovered in
a submultiframe 1 received at the far end; and if E2 =
0, a CRC-4 error was discovered in a submultiframe
2 received at the far end. No submultiframe
sequence numbers or re-transmission capabilities
are supported with layer 1 PCM 30 protocol. See
ITU-T G.704 and G.706 for more details on the
operation of CRC-4 and E-bits.
There are two CRC multiframe alignment algorithm
options selected by the AUTC control bit (address
10H, page 01H). When AUTC is zero, automatic
CRC-to-non-CRC interworking is selected. When
AUTC is one and ARAI is low, if CRC-4 multiframe
alignment is not found in 400 msec, the transmit RAI
will be continuously high until CRC-4 multiframe
alignment is achieved.
The control bit for transmit E bits (TE, address 11H
of page 01H) will have the same function in both
states
of
AUTC.
That
synchronization is not achieved the state of the
transmit E-bits will be the same as the state of the
TE control bit. When CRC-4 synchronization is
achieved the transmit E-bits will function as per ITU-
T G.704. Table 12 outlines the operation of the
AUTC, ARAI and TALM control bits of the MT9074.
is,
when
CRC-4
CAS Signalling Multiframing in E1 mode
The purpose of the signalling multiframing algorithm
is to provide a scheme that will allow the association
of a specific ABCD signalling nibble with the
appropriate PCM 30 channel. Time slot 16 is
reserved for the communication of Channel
Associated Signalling (CAS) information (i.e., ABCD
signalling bits for up to 30 channels). Refer to ITU-T
Table 12 - Operation of AUTC, ARAI and TALM Control Bits (E1 Mode)
AUTC
ARAI
TALM
Description
0
0
X
Automatic CRC-interworking is activated. If no valid CRC MFAS is being
received, transmit RAI will flicker high with every reframe (8msec.), this cycle
will continue for 400 msec., then transmit RAI will be low continuously. The
device will stop searching for CRC MFAS, continue to transmit CRC-4
remainders, stop CRC-4 processing, indicate CRC-to-non-CRC operation
and transmit E-bits to be the same state as the TE control bit (page 01H,
address 16H).
0
1
0
Automatic CRC-interworking is activated. Transmit RAI is low continuously.
0
1
1
Automatic CRC-interworking is activated. Transmit RAI is high continuously.
1
0
X
Automatic CRC-interworking is de-activated. If no valid CRC MFAS is being
received, transmit RAI flickers high with every reframe (8 msec.), this cycle
continues for 400 msec, then transmit RAI becomes high continuously. The
device continues to search for CRC MFAS and transmit E-bits are the same
state as the TE control bit. When CRCSYN = 0, the CRC MFAS search is
terminated and the transmit RAI goes low.
1
1
0
Automatic CRC-interworking is de-activated. Transmit RAI is low
continuously.
1
1
1
Automatic CRC-interworking is de-activated. Transmit RAI is high
continuously.
相關PDF資料
PDF描述
MT9074AP T1/E1/J1 Single Chip Transceiver
MT9074 T1/E1/J1 Single Chip Transceiver(T1/E1/J1單片收發器)
MT9075B E1 Single Chip Transceiver
MT9075B E1 Single Chip Transceiver(E1單片收發器)
MT9075 E1 Single Chip Transceiver
相關代理商/技術參數
參數描述
MT9074AL1 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 5V 100MQFP - Trays
MT9074AP 制造商:Microsemi Corporation 功能描述:
MT9074AP1 制造商:Microsemi Corporation 功能描述:T1/E1/J1 SGLE CHIP XSCR 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 5V 68PLCC - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL T1/E1 68PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX SGL T1/E1 68PLCC
MT9074APR 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 Single Chip Transceiver
MT9074APR1 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 5V 68PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 5V 68PLCC - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*