參數資料
型號： MT9076
廠商： Mitel Networks Corporation
英文描述： T1/E1/J1 3.3V Single Chip Transceiver
中文描述： T1/E1/J1收發3.3V的單芯片收發器
文件頁數： 3/160頁
文件大?。?/td> 416K
代理商： MT9076
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
Preliminary Information
MT9076
3
Pin Description
Pin #
Name
Description
PLCC LQFP
1
51
OSC1
Oscillator (3V Input).
This pin is either connected via a 20.000 MHz crystal to OSC2
where a crystal is used, or is directly driven when a 20.000 MHz. oscillator is employed.
2
52
OSC2
Oscillator (3V Output).
Connect a 20.0 MHz crystal between OSC1 and OSC2. Not
suitable for driving other devices.
3
53
V
SS4
V
DD4
CSTo
Negative Power Supply .
Digital ground.
4
54
Positive Power Supply .
Digital supply (+3.3V
±
5%).
5
55
Control ST-BUS (5V tolerant Output)
. CSTo carries serial streams for CAS and CCS
respectively a 2.048 Mbit/s ST-BUS status stream which contains the 30 receive
signaling nibbles (ABCDZZZZ or ZZZZABCD). The most significant nibbles of each ST-
BUS time slot are valid and the least significant nibbles of each ST-BUS time slot are
tristated when control bit MSN (page 01H, address 1AH, bit 1) is set to 1. If MSN=0, the
position of the valid and tristated nibbles are reversed.
6
56
CSTi
Control ST-BUS (5V tolerant Input)
. CSTi carries serial streams for CAS and CCS
respectively a 2.048 Mbit/s ST-BUS control stream which contains the 30 transmit
signaling nibbles (ABCDXXXX or XXXXABCD) when RPSIG=0. When RPSIG=1 this
pin has no function. The most significant nibbles of each ST-BUS time slot are valid and
the least significant nibbles of each ST-BUS time slot are ignored when control bit MSN
(page 01H, address 1AH, bit 1) is set to 1. If MSN=0, the position of the valid and
ignored nibbles is reversed.
7
57
DSTo
Data ST-BUS (5V tolerant Output).
A 2.048 Mbit/s serial stream which contains the
24/30 PCM(T1/E1) or data channels received on the PCM 24/30 (T1/E1) line.
8
58
DSTi
Data ST-BUS (5V tolerant Input).
A 2.048 Mbit/s serial stream which contains the
24/30 (T1/E1) PCM or data channels to be transmitted on the PCM 24/30 (T1/E1)
line.
9
59
DS/RD
Data/Read Strobe (5V tolerant Input)
.
In Motorola mode (DS), this input is the active low data strobe of the processor
interface. In Intel mode (RD), this input is the active low read strobe of the processor
interface.
10
63
CS
Chip Select (5V tolerant Input)
. This active low input enables the non-multiplexed
parallel microprocessor interface of the MT9076. When CS is set to high, the
microprocessor interface is idle and all bus I/O pins will be in a high impedance state.
11
64
RESET
RESET (5V tolerant Input).
This active low input puts the MT9076 in a reset condition.
RESET should be set to high for normal operation. The MT9076 should be reset after
power-up. The RESET pin must be held low for a minimum of 1
μ
sec. to reset the device
properly.
12
65
IRQ
Interrupt Request (5V tolerant Output).
A low on this output pin indicates that an
interrupt request is presented. IRQ is an open drain output that should be connected to
V
DD
through a pull-up resistor. An active low CS signal is not required for this pin to
function.
13 -
16
66-69
D0 - D3
Data 0 to Data 3 (5V tolerant Three-state I/O)
. These signals combined with D4-D7
form the bidirectional data bus of the parallel processor interface (D0 is the least
significant bit).
17
70
VSS5
Negative Power Supply.
Digital ground.
18
71
IC4
Internal Connection (3V Input).
Tie to V
SS
(Ground) for normal operation.
相關PDF資料
PDF描述
MT9076AB T1/E1/J1 3.3V Single Chip Transceiver
MT9076 T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器)
MT9079 Advanced Controller for E1(先進的E1幀調節器和控制器)
MT9080B SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊)
MT90810 Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路)
相關代理商/技術參數
參數描述
MT9076AB 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076AP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076B 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver
MT9076BB 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
MT9076BB1 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*