- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9076 (Mitel Networks Corporation) T1/E1/J1 3.3V Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9076 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/J1 3.3V Single Chip Transceiver |
| 中文描述： | T1/E1/J1收發3.3V的單芯片收發器 |
| 文件頁數： | 58/160頁 |
| 文件大?。?/td> | 416K |
| 代理商： | MT9076 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
MT9076
Preliminary Information
54
15.7
Transmit Message
When bit seven (TXMSG) in the Per Time Slot Control Word is set the data transmit in the selected channel is
sourced from the transmit message word in Master Control page 1.
16.0 Alarms
The following alarms are detected by the receiver in T1 mode. Each may generate a maskable interrupt:
D4 Yellow Alarm - in D4 mode there are two possible yellow alarm signals. If control bit D4SECY is set low,
(page 1H, address 11H, bit 1) the criteria for a yellow alarm is an excess of ’0’s (more than 285) in bit position
2 of incoming DS0 channels during an integration period of 1.5 milliseconds. It is cleared after more than 3 ’1’s
are detected in bit position 2 of normal data in a 1.5 millisecond integration period. If D4SECY is set high the
secondary yellow alarm is selected. The detection criteria becomes 2 consecutive ’1’s in the Sbit position of the
12th frame.
ESF Yellow Alarm - In ESF mode, there are two possible yellow alarm signals. If control bit JYEL (page 1H,
address 14H, bit 0) is set low the criteria for a yellow alarm is a pattern 00000000 11111111 in seven or more
code words out of ten, If JYEL is set high, the criteria for a yellow alarm is a pattern 11111111 11111111 in
seven or more code words out of ten.
All Ones - This bit (page 3H, address 11H, bit 3) is set if less than six zeros are received on the incoming line
data during a 3 ms interval
Loss of Signal - a loss of signal condition occurs when the receive signal level is lower than 20dB or 40 dB
below the nominal signal level for at least a millisecond or when 32 or 192 (control bit L32Z (page 01H, address
19H, bit 1) consecutive zeros have been received. A loss of signal condition will terminate when an average
ones density of at least 12.5% has been received over a period of 193 contiguous pulse positions starting with
a pulse. The loss of signal is reported in the Receive Signal Status Word - (page 3, address 16H bit 4).
The following alarms are detected by the receiver in E1 mode. Each may generate a maskable interrupt:
Remote Alarm Indication (RAI) - bit 3 (A) of the receive NFAS;
Alarm Indication Signal (AIS) - unframed all ones signal for at least a double frame (512 bits) or two double
frames (1024 bits);
Channel 16 Alarm Indication Signal - all ones signal in channel 16;
Auxiliary pattern - 101010... pattern for at least 512 bits;
Loss of Signal - a loss of signal condition occurs when the receive signal level is lower than 20dB or 40 dB (by
setting the bit ELOS on page 02H, address 10H, bit 3) below the nominal signal level for more than a
millisecond or when more than 32 or 192 (control bit L32Z (page 01H, address 19H 9 bit 1) zeros have been
received in a row. A loss of signal condition will terminate when an average ones density of at least 12.5% has
been received over a period of 192 contiguous pulse positions starting with a pulse.
Remote signaling Multiframe Alarm - (Y-bit) of the multiframe alignment signal.
The alarm reporting latch (address 12H page 04H) contains a register whose bits are set high for selected
alarms. These bits stay high until the register is read. This allows the controller to record intermittent or
sporadic alarm occurances.
16.1
Automatic Alarms
In E1 mode, the transmission of RAI and signaling multiframe alarms can be made to function automatically
from control bits ARAI and AUTY (page 01H, address 10H). When ARAI = 0 and basic frame synchronization is
lost (SYNC = 1), the MT9076 will automatically transmit the RAI alarm signal to the far end of the link. The
transmission of this alarm signal will cease when basic frame alignment is acquired.
When AUTY = 0 and signaling multiframe alignment is not acquired (MFSYNC = 1), the MT9076 will
automatically transmit the multiframe alarm (Y-bit) signal to the far end of the link. This transmission will cease
when signaling multiframe alignment is acquired.
相關PDF資料 |
PDF描述 |
|---|---|
| MT9076AB | T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
| MT9080B | SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊) |
| MT90810 | Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9076AB | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
| MT9076BB | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BB1 | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
發布緊急采購，3分鐘左右您將得到回復。