- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9076 (Mitel Networks Corporation) T1/E1/J1 3.3V Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9076 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/J1 3.3V Single Chip Transceiver |
| 中文描述： | T1/E1/J1收發3.3V的單芯片收發器 |
| 文件頁數： | 59/160頁 |
| 文件大小： | 416K |
| 代理商： | MT9076 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
Preliminary Information
MT9076
55
17.0 Detected Events
17.1
T1 mode
17.1.1
In T1 mode, bit 5 page 3H address 10H toggles whenever a sliding window detects 2 framing errors events (Ft or
ESF) in a sliding window of 6.
Severely Errored Frame Event
17.1.2
T1.403 defines SF mode line loopback activate and deactivate codes. These codes are either a framed or un-
framed repeating bit sequence of 00001 for activation or 001 for deactivation. The standard goes on to say that
these codes will persist for five seconds or more before the loopback action is taken. In T1 mode MT9076 will
detect both framed and unframed line activate and de-activate codes even in the presence of a BER of 3 x 10-
3. Line Loopback Disable Detect - LLDD - in the Alarm Status Word (bit 0 address 11H of page 3H) will be
asserted when a repeating 001 pattern (either framed or unframed) has persisted for 48 milliseconds. Line
Loopback Enable Detect LLED in the Alarm Status Word will be asserted when a repeating 00001 pattern
(either framed or unframed) has persisted for 48 milliseconds.
Loop Code Detect
17.1.3
In T1 mode, bit 2 of address 11H on page 3H (PDV) toggles if the receive data fails to meet ones density
requirements. It will toggle upon detection of 16 consecutive zeros on the line data, or if there are less than N
ones in a window of 8(N+1) bits - where N = 1 to 23.
Pulse Density Violation Detect
17.1.4
In T1 mode, MT9076 has a one second timer derived from the 20 Mhz oscillator pins. The timer may be used to
trigger interrupts for T1.403/408 performance messaging.
Timer Outputs
17.2
E1 mode
17.2.1
Two consecutive frame alignment signals in error.
Consecutive Frame Alignment Patterns (CONFAP)
17.2.2
These bits are received on the PCM 30 and link in bit positions two to eight of time slot 0 - frame alignment
signal. These signals form the frame alignment signal and should be 0011011.
Receive Frame Alignment Signals
17.2.3
This signal is received on the PCM 30 and link in bit position two of time slot 0 - non frame alignment signal.
Receive Non Frame Alignment Signal
17.2.4
These signal are received on the PCM 30 and link in bit position one to four of time slot 16 of frame zero of
every signaling multiframe.
Receive Multiframe Alignment Signals
18.0 Interrupts
The MT9076 has an extensive suite of maskable interrupts, which are divided into four categories based on the
type of event that caused the interrupt. Each interrupt has an associated mask and interrupt bit. When an
unmasked interrupt event occurs, IRQ will go low and one or more bits of the appropriate interrupt register will
go high(T1/E1). After each interrupt register is read it is automatically cleared. When all interrupt registers are
cleared IRQ will return to a high impedance state. This function can also be accomplished by toggling the INTA
bit (page 1, address 1AH.)
相關PDF資料 |
PDF描述 |
|---|---|
| MT9076AB | T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
| MT9080B | SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊) |
| MT90810 | Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9076AB | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
| MT9076BB | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BB1 | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
發布緊急采購，3分鐘左右您將得到回復。