參數資料
型號： MT9076
廠商： Mitel Networks Corporation
英文描述： T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器)
中文描述： T1/E1/J1收發3.3V的單芯片收發器（T1/E1/J1收發3.3單片收發器）
文件頁數： 74/162頁
文件大?。?/td> 427K
代理商： MT9076
MT9076
Preliminary Information
70
Bit
Name
Functional Description
7
T1/E1
T1/E1 mode selection.
when this bit is zero, the device is in T1 mode. When set high, the device
is in E1 mode.
6
--
Reserved.
Must be kept at 0 for normal operation.
5
TxEN
Transmit Enable.
Setting this bit low turns off the TTIP and TRING output line drivers. Setting this
bit high enables them.
4
LIUEn
LIU Enable.
Setting this bit low enables the internal LIU front-end. Setting this pin high disables
the LIU. Digital inputs RXA and RXB are sampled by the rising edge of E1.5i (Exclk) to strobe in
the received line data. Digital transmit data is clocked out of pins TXA and TXB with the rising edge
of Exclk
3
ELOS
ELOS Enable
. Set this bit low to set the analog loss of signal threshold to 40 dB below nominal.
Set this bit high to set the analog loss of signal threshold to 20 dB below nominal.
2
Tx8KEN
Transmit 8 KHz Enable.
If one, the pin RxMF/TxFP transmits a positive 8 KHz frame pulse
synchronous with the serial data stream transmit on TXA/TXB. If zero, the pin RxMF/TxFP
transmits a negative frame pulse synchronous with the multiframe boundary of data coming out of
DSTo.
1
ADSEQ
Digital Milliwatt or Digital Test Sequence
. If one, the Alaw digital milliwatt analog test sequence
will be selected for those channels with per time slot control bits TTST, RRST set. If zero, a PRBS
generator / detector will be connected to channels with TTST, RRST respectively.
0
--
Reserved.
Must be kept at 0 for normal operation.
Table 37 - Configuration Control Word
(Page 2, Address 10H) (T1)
Bit
Name
Functional Description
7-5
--
Reserved.
Must be kept at 0 for normal operation.
4
--
Reserved.
Set low for normal operation.
3
CPL
Custom Pulse Level.
Setting this bit low enables the internal ROM values in generating the
transmit pulses. The ROM is coded for different line terminations or build out, as specified in the
LIU Control word. Setting this pin high disables the pre-programmed pulse templates. Each of
the 4 phases that generate a mark derive their D/A coefficients from the values programmed in
the CPW registers.
2-0
TXLB2-0
Transmit Line Build Out 2 - 0
. Setting these bits shapes the transmit pulse as detailed in the
table below:
TX22
TXL1
TXL0
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
After reset these bits are zero.
Line Build Out
0 to 133 feet/ 0 dB
133 to 266 feet
266 to 399 feet
399 to 533 feet
533 to 655 feet
-7.5 dB
-15 dB
-22.5 dB
Table 38 - LIU Tx Word
(Page 2, Address 11H) (T1)
相關PDF資料
PDF描述
MT9079 Advanced Controller for E1(先進的E1幀調節器和控制器)
MT9080B SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊)
MT90810 Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路)
MT90812 Integrated Digital Switch (IDX)(集成數字開關)
MT90840AK Distributed Hyperchannel Switch
相關代理商/技術參數
參數描述
MT9076AB 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076AP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076B 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver
MT9076BB 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
MT9076BB1 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*