參數資料
型號: TMX320TCI6482
廠商: Texas Instruments, Inc.
元件分類: 數字信號處理
英文描述: Communications Infrastructure Digital Signal Processor
中文描述: 通信基礎設施的數字信號處理器
文件頁數: 126/255頁
文件大?。?/td> 1893K
代理商: TMX320TCI6482
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁當前第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁
www.ti.com
8.6.2
Warm Reset (RESET Pin)
TMS320TCI6482
Communications Infrastructure Digital Signal Processor
SPRS246F–APRIL 2005–REVISED MAY 2007
all the system clocks are invalid at this point.
The RESETSTAT pin stays asserted (low), indicating the device is in reset.
3. The POR pin may now be deasserted (driven high).
When the POR pin is deasserted, the configuration pin values are latched and the PLL controllers
change their system clocks to their default divide-down values. PLL2 is taken out of reset and
automatically starts its locking sequence. Other device initialization is also started.
4. After device initialization is complete, the RESETSTAT pin is deasserted (driven high). By this time,
PLL2 has already completed its locking sequence and is outputting a valid clock. The system clocks of
both PLL controllers are allowed to finish their current cycles and then paused for 10 cycles of their
respective system reference clocks. After the pause the system clocks are restarted at their default
divide-by settings.
5. The device is now out of reset, device execution begins as dictated by the selected boot mode (see
Section 2.4
,
Boot Sequence
).
NOTE
To most of the device, reset is de-asserted only when the POR and RESET pins are both
de-asserted (driven high). Therefore, in the sequence described above, if the RESET pin
is held low past the low period of the POR pin, most of the device will remain in reset. The
only exception being that PLL2 is taken out of reset as soon as POR is de-asserted
(driven high), regardless of the state of the RESET pin. The RESET pin should not be tied
together with the POR pin.
A Warm Reset has the same effects as a Power-on Reset, except that in this case, the test and emulation
logic and PLL2 are not reset.
The following sequence must be followed during a Warm Reset:
1. Hold the RESET pin low for a minimum of 24 CLKIN1 cycles. Within the minimum 24 CLKIN1 cycles.
Within the low period of the RESET pin, the following happens:
The Z group pins, low group pins, and the high group pins are set to their reset state with one
exception:
The PCI pins are not affected by warm reset if the PCI module was enabled before RESET went
low. In this case, PCI pins stay at whatever their value was before RESET went low.
The reset signals flow to the entire chip (excluding the test and emulation logic), resetting modules
that use reset asynchronously.
The PLL1 controller is reset thereby switching back to bypass mode and resetting all its registers to
their default values. PLL1 is placed in reset and loses lock. The PLL1 controller clocks start running
at the frequency of the system reference clock. The clocks are propagated throughout the chip to
reset modules that use reset synchronously.
The PLL2 controller is reset thereby resetting all its registers to their default values. The PLL2
controller clocks start running at the frequency of the system reference clock. PLL2 is not reset,
therefore it remains locked.
The RESETSTAT pin becomes active (low), indicating the device is in reset.
2. The RESET pin may now be released (driven inactive high).
When the RESET pin is released, the configuration pin values are latched and the PLL controllers
immediately change their system clocks to their default divide-down values. Other device initialization
is also started.
3. After device initialization is complete, the RESETSTAT pin goes inactive (high). All system clocks are
allowed to finish their current cycles and then paused for 10 cycles of their respective system reference
clocks. After the pause the system clocks are restarted at their default divide-by settings.
4. The device is now out of reset, device execution begins as dictated by the selected boot mode (see
C64x+ Peripheral Information and Electrical Specifications
126
Submit Documentation Feedback
相關PDF資料
PDF描述
TMX320TCI6482ZTZ Communications Infrastructure Digital Signal Processor
TMX320TCI6482ZTZ8 Communications Infrastructure Digital Signal Processor
TMX320TCI6482ZTZA Communications Infrastructure Digital Signal Processor
TMX320TCI6482ZTZA8 Communications Infrastructure Digital Signal Processor
TMX380SRAFNL Communications Interface
相關代理商/技術參數
參數描述
TMX320TCI6482ZTZ 制造商:Texas Instruments 功能描述:DSP FIX PT 32BIT 1GHZ 8000MIPS 697FCBGA - Trays
TMX320TCI6616XCYP 制造商:Texas Instruments 功能描述:
TMX320VC33PGE 制造商:Texas Instruments 功能描述:
TMX320VC5401PGE50 制造商:Rochester Electronics LLC 功能描述:- Bulk
TMX320VC5402GGLL100 制造商:Rochester Electronics LLC 功能描述:- Bulk