- 您現在的位置：買賣IC網 > PDF目錄385951 > TVP3025-135 (Texas Instruments, Inc.) Video Interface PALETTE(三PLL，視頻接口調色器) PDF資料下載
參數資料
| 型號： | TVP3025-135 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Video Interface PALETTE(三PLL，視頻接口調色器) |
| 中文描述： | 視頻接口盒（三鎖相環，視頻接口調色器） |
| 文件頁數： | 46/99頁 |
| 文件大小： | 663K |
| 代理商： | TVP3025-135 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
2–32
When both the 64 x 64 user-definable cursor and the crosshair cursor are enabled, cursor-control register
bit 5 specifies the display at the intersection of the crosshair cursor and the 64
×
64 user-definable cursor.
The following cursor intersection truth table details the results of all cursor color combinations; see
Section 2.3.18.3 for specific cursor-control register bit definitions.
CROSSHAIR
64 x 64 CURSOR
CCR5 = 0
CCR5 = 1
Color 0
Transparent
Color 0
Color 0
Color 1
Transparent
Color 1
Color 1
Color 0
Complement
Color 0
Color 0
Color 1
Complement
Color 1
Color 1
Color 0
Color 0
Color 0
Transparent
Color 1
Color 0
Color 1
Transparent
Color 0
Color 1
Color 0
Complement
Color 1
Color 1
Color 1
Complement
2.3.10
The TVP3025 provides three integrated mechanisms for switching between VGA or overlay images and
direct-color images midscreen. The auxiliary window function supports the display of overlay or VGA
graphics into a specified window on the screen when in a direct-color mode. The same window registers
used to define the crosshair cursor window are used to define the auxiliary window start and window stop
(see Sections 2.3.18.6 and 2.3.18.7). One application of this function is to fit a VGA picture in the middle
of a direct-color display. The port-select function utilizes an external terminal (PSEL) to switch between VGA
or overlay and direct-color on a pixel-by-pixel basis, enabling the generation of multiple VGA or overlay
windows on a direct-color screen.
Auxiliary Window, Port Select, and Color-Key Switching
The auxiliary-window and port-select functions are integrated so that they can be enabled simultaneously
or separately. They are only operable when in one of the direct-color modes, since both VGA and overlay
utilize the palette RAM. Overlay windowing is not supported for those direct-color modes that do not have
overlay capability. If VGA windowing is to be performed, multiplex-control register 2 needs to have bit 7 set
to a logic 1 (activating the VGA port) and the appropriate direct-color mode must be chosen with the
remaining multiplex-control register bits. When the VGA port is activated (MCR2 bit 7 = 1), the overlay is
disabled.
The auxiliary-window and port-select functions are controlled by the auxiliary-control register, which is
programmed through the indirect register map (29 hex, see Section 2.3.18.11 for register bit definitions).
Like the crosshair cursor window, for auxiliary graphics to be displayed, both the window-start and window-
stop registers must contain locations on the active screen. If full-screen auxiliary graphics is desired, the
window-start (x,y) registers should contain 0000 (hex) and the window-stop (x,y) registers should be set to
the last active pixel location. The window-start registers can be programmed with a location off the active
screen to temporarily remove the auxiliary window without disabling the function entirely.
The color-key switching function allows switching between VGA or overlay and direct-color on a
pixel-by-pixel basis by comparing the incoming VGA/overlay and direct-color data with user-programmable
color-key ranges. The color-key ranges are set by writing to the eight 8-bit color-key range registers:
color-key red (low, high), color-key green (low, high), color-key blue (low, high), and color-key OL/VGA (low,
high). The color-key switching function is controlled by the color-key-control register (see Section 2.3.9.2)
All of the registers can be programmed through the indirect register map. When the VGA port is activated
(MCR2 bit 7 = 1), the color-key OL/VGA register (low, high) color comparison is performed on VGA data
and the VGA port is color-key switched instead of overlay.
The windowing and color-key switching functions are integrated much like a logical OR function. If either
of the functions switches to palette graphics (VGA or overlay through the palette RAM), palette graphics are
相關PDF資料 |
PDF描述 |
|---|---|
| TVP3025-175 | Video Interface PALETTE(三PLL，視頻接口調色器) |
| TVP3030-175 | Video Interface PALETTE Exract(1600×1200，24位真彩色視頻接口調色器) |
| TVP3030-220 | Video Interface PALETTE Exract(1600×1200，24位真彩色視頻接口調色器) |
| TVP3030-250 | Video Interface PALETTE Exract(1600×1200，24位真彩色視頻接口調色器) |
| TVP3409-170 | Advanced Video Interface PALETTE(雙PLL，視頻接口調色器真彩色CMOS) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TVP3025-135PCE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette |
| TVP3025-175PCE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette |
| TVP3025-220MDN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette |
| TVP3025-220PCE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC with Color Palette (RAMDAC) |
| TVP3026 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Video Interface Palette |
發布緊急采購，3分鐘左右您將得到回復。