參數資料
型號: V30MZ
英文描述: V30MZ(TM) Hardware (Preliminary) | User's Manual[01/2002]
中文描述: V30MZ(TM)硬件(初步)|用戶手冊[01/2002]
文件頁數: 3/89頁
文件大?。?/td> 418K
代理商: V30MZ
3
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note:
Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity
as much as possible, and quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using
insulators that easily build static electricity. Semiconductor devices must be stored and transported
in an anti-static container, static shielding bag or conductive material. All test and measurement
tools including work bench and floor should be grounded. The operator should be grounded using
wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need
to be taken for PW boards with semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note:
No connection for CMOS device inputs can be cause of malfunction. If no connection is provided
to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence
causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels
of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused
pin should be connected to V
DD
or GND with a resistor, if it is considered to have a possibility of
being an output pin. All handling related to the unused pins must be judged device by device and
related specifications governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note:
Power-on does not necessarily define initial status of MOS device. Production process of MOS
does not define the initial operation status of the device. Immediately after the power source is
turned ON, the devices with reset function have not yet been initialized. Hence, power-on does
not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after power-on for devices
having reset function.
V30MZ, V30HL, V30MX, and V Series are trademarks of NEC Corporation.
相關PDF資料
PDF描述
V32FB-V42D-MMMME MODEM Chip Set
DSP16A-F14-033 16-Bit Digital Signal Processor
DSP16A-F14-033I 16-Bit Digital Signal Processor
DSP16A-F14-055 16-Bit Digital Signal Processor
DSP16A-F14-055I 16-Bit Digital Signal Processor
相關代理商/技術參數
參數描述
V30N 制造商:Renesas Electronics Corporation 功能描述:
V-30TB 制造商:Mencom 功能描述:
V31 制造商:SMC Corporation of America 功能描述:CONNECTOR
V3-1 功能描述:基本/快動開關 15.1A pin plunger Screw Terminals RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel
V3-1001 功能描述:基本/快動開關 Snap Action SPDT 10A 3.89N Thru-Hole RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel