參數資料
型號： XC2S200E-6FGG456C
廠商： Xilinx Inc
文件頁數： 30/108頁
文件大?。?/td> 0K
描述： IC SPARTAN-IIE FPGA 200K 456FBGA
標準包裝： 60
系列： Spartan®-IIE
LAB/CLB數： 1176
邏輯元件/單元數： 5292
RAM 位總計： 57344
輸入/輸出數： 289
門數： 200000
電源電壓： 1.71 V ~ 1.89 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 456-BBGA
供應商設備封裝： 456-FBGA
其它名稱： 122-1323
28
DS077-2 (v3.0) August 9, 2013
Product Specification
Spartan-IIE FPGA Family: Functional Description
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
If CCLK is slower than FCCNH, the FPGA will never assert
BUSY. In this case, the above handshake is unnecessary,
and data can simply be entered into the FPGA every CCLK
cycle.
A configuration packet does not have to be written in one
continuous stretch, rather it can be split into many write
sequences. Each sequence would involve assertion of CS.
In applications where multiple clock cycles may be required
to access the configuration data before each byte can be
loaded into the Slave Parallel interface, a new byte of data
may not be ready for each consecutive CCLK edge. In such
a case the CS signal may be deasserted until the next byte
is valid on D0-D7. While CS is High, the Slave Parallel inter-
face does not expect any data and ignores all CCLK transi-
tions. However, to avoid aborting configuration, WRITE
must continue to be asserted while CS is asserted during
CCLK transitions.
Abort
To abort configuration during a write sequence, deassert
WRITE while holding CS Low. The abort operation is initi-
ated at the rising edge of CCLK. The device will remain
BUSY until the aborted operation is complete. After aborting
configuration, data is assumed to be unaligned to word
boundaries and the FPGA requires a new synchronization
word prior to accepting any new packets.
Boundary-Scan Configuration Mode
In the boundary-scan mode, no nondedicated pins are
required, configuration being done entirely through the
IEEE 1149.1 Test Access Port (TAP).
Configuration through the TAP uses the special CFG_IN
instruction. This instruction allows data input on TDI to be
converted into data packets for the internal configuration
bus.
The following steps are required to configure the FPGA
through the boundary-scan port.
1.
Load the CFG_IN instruction into the boundary-scan
instruction register (IR)
2.
Enter the Shift-DR (SDR) state
3.
Shift a standard configuration bitstream into TDI
4.
Return to Run-Test-Idle (RTI)
5.
Load the JSTART instruction into IR
6.
Enter the SDR state
7.
Clock TCK (if selected) through the startup sequence
(the length is programmable)
8.
Return to RTI
Configuration and readback via the TAP is always available.
The boundary-scan mode simply locks out the other modes.
The boundary-scan mode is selected by a <10x> on the
mode pins (M0, M1, M2). Note that the PROGRAM pin must
be pulled High prior to reconfiguration. A Low on the PRO-
GRAM pin resets the TAP controller and no boundary scan
operations can be performed. See Xilinx Application Note
XAPP188 for more information on boundary-scan configu-
ration.
Readback
The configuration data stored in the Spartan-IIE FPGA con-
figuration memory can be read back for verification. Along
with the configuration data it is possible to read back the
contents of all flip-flops/latches, LUT RAMs, and block
RAMs. This capability is used for real-time debugging.
For more detailed information see Xilinx Application Note
XAPP176, Configuration and Readback of the Spartan-II
and Spartan-IIE FPGA Families.
Figure 21: Loading Configuration Data for the Slave
Parallel Mode
Yes
No
FPGA
Driving BUSY
High?
After INIT
Goes High
Load One
Configuration
Byte on Next
CCLK Rising Edge
To CRC Check
DS001_19_032300
No
End of
Configuration
Data File?
Yes
User Drives
WRITE and CS
Low
User Drives
WRITE and CS
High
相關PDF資料
PDF描述
XC2S200E-6FG456C IC FPGA 1.8V 1176 CLB'S 456-FPGA
93C86CT-E/SN IC EEPROM 16KBIT 3MHZ 8SOIC
XA6SLX16-2FTG256Q IC FPGA SPARTAN 6 256FTGBGA
GMC20DTEN CONN EDGECARD 40POS .100 EYELET
93C86C-E/SN IC EEPROM 16KBIT 3MHZ 8SOIC
相關代理商/技術參數
參數描述
XC2S200E-6FGG456I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S200E-6FGG676C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S200E-6FGG676I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S200E6FT256C 制造商:Xilinx 功能描述:
XC2S200E-6FT256C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE 1.8V FPGA Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*