參數資料
型號: XC2S200E-6FGG456C
廠商: Xilinx Inc
文件頁數: 36/108頁
文件大小: 0K
描述: IC SPARTAN-IIE FPGA 200K 456FBGA
標準包裝: 60
系列: Spartan®-IIE
LAB/CLB數: 1176
邏輯元件/單元數: 5292
RAM 位總計: 57344
輸入/輸出數: 289
門數: 200000
電源電壓: 1.71 V ~ 1.89 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 85°C
封裝/外殼: 456-BBGA
供應商設備封裝: 456-FBGA
其它名稱: 122-1323
DS077-3 (v3.0) August 9, 2013
33
Product Specification
Spartan-IIE FPGA Family: DC and Switching Characteristics
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
Power-On Requirements
Spartan-IIE FPGAs require that a minimum supply current
ICCPO be provided to the VCCINT lines for a successful
power-on. If more current is available, the FPGA can con-
sume more than ICCPO min., though this cannot adversely
affect reliability.
A maximum limit for ICCPO is not specified. Be careful when
using foldback/crowbar supplies and fuses. It is possible to
control the magnitude of ICCPO by limiting the supply current
available to the FPGA. A current limit below the trip level will
avoid inadvertently activating over-current protection cir-
cuits.
DC Input and Output Levels
Values for VIL and VIH are recommended input voltages.
Values for VOL and VOH are guaranteed output voltages
over the recommended operating conditions. Only selected
standards are tested. These are chosen to ensure that all
standards meet their specifications. The selected standards
are tested at minimum VCCO with the respective IOL and IOH
currents shown. Other standards are sample tested.
Symbol
Description
Min(1)
Typ
Max
Units
ICCPO
Total VCCINT supply current
required during power-on
Commercial
XC2S50E - XC2S300E
After PCN(2)
300
-
mA
Before
PCN(2)
500
-
mA
XC2S400E - XC2S600E
500
-
mA
Industrial
XC2S50E - XC2S300E
After PCN(2)
500
-
mA
Before
PCN(2)
2
-
A
XC2S400E - XC2S600E
700
-
mA
TCCPO
VCCINT(3,4) ramp time
After PCN(2)
500
-
μs
Before PCN(2)
2
-
50
ms
IHSPO
AC current per pin during power-on in
hot-swap applications when
VIN > VCCO + 0.4V; duration < 10ns
After PCN(2)
-
±60
-
μA
Notes:
1.
The ICCPO requirement applies for a brief time (commonly only a few milliseconds) when VCCINT ramps from 0 to 1.8V.
2.
Devices built after the Product Change Notice PCN 2002-05 (see
after the PCN have a ‘T’ preceding the date code as referenced in the PCN. Note that the XC2S150E, XC2S400E, and XC2S600E
always have this mark. Devices before the PCN have an ‘S’ preceding the date code. Note that devices before the PCN are
measured with VCCINT and VCCO powering up simultaneously.
3.
The ramp time is measured from GND to 1.8V on a fully loaded board.
4.
VCCINT must not dip in the negative direction during power on.
5.
I/Os are not guaranteed to be disabled until VCCINT is applied.
6.
For more information on designing to meet the power-on specifications, refer to the application note XAPP450 "Power-On Current
Input/Output
Standard
VIL
VIH
VOL
VOH
IOL
IOH
V, Min
V, Max
V, Min
V, Max
V, Min
mA
LVTTL(1)
–0.5
0.8
2.0
3.6
0.4
2.4
24
–24
LVCMOS2
–0.5
0.7
1.7
2.7
0.4
1.9
12
–12
LVCMOS18
–0.5
35% VCCO
65% VCCO
1.95
0.4
VCCO – 0.4
8
–8
PCI, 3.3V
–0.5
30% VCCO
50% VCCO
VCCO + 0.5
10% VCCO
90% VCCO
Note (2)
GTL
–0.5
VREF – 0.05
VREF + 0.05
3.6
0.4
-
40
-
GTL+
–0.5
VREF – 0.1
VREF + 0.1
3.6
0.6
-
36
-
相關PDF資料
PDF描述
XC2S200E-6FG456C IC FPGA 1.8V 1176 CLB'S 456-FPGA
93C86CT-E/SN IC EEPROM 16KBIT 3MHZ 8SOIC
XA6SLX16-2FTG256Q IC FPGA SPARTAN 6 256FTGBGA
GMC20DTEN CONN EDGECARD 40POS .100 EYELET
93C86C-E/SN IC EEPROM 16KBIT 3MHZ 8SOIC
相關代理商/技術參數
參數描述
XC2S200E-6FGG456I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S200E-6FGG676C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S200E-6FGG676I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE FPGA
XC2S200E6FT256C 制造商:Xilinx 功能描述:
XC2S200E-6FT256C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-IIE 1.8V FPGA Family