V
參數資料
型號： XR88C681CJ-F
廠商： Exar Corporation
文件頁數： 37/101頁
文件大?。?/td> 0K
描述： IC UART CMOS DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1327-5
XR88C681
40
Rev. 2.11
CPU
-INT
-IACK
-INTR
IEI
IEO
-IACK
-INTR
IEI
IEO
-IACK
-INTR
IEI
IEO
-IACK
-INTR
IEI
IEO
-IACK
VCC
HIGHEST
LOWEST
PRIORITY
Figure 15. A Diagram of Numerous DUARTs Configured in an Interrupt
Daisy Chain (for Z-Mode Operation)
VCC
In addition to the -INTR and -IACK pins, the Z-Mode
DUART also uses the IEI and IEO pins; which are defined
as follows:
IEI - Interrupt Enable Input
This active-high input is only available if the DUART is
configured to operate in the Z-Mode. If this input is at a
logic “high” then all unmasked interrupt requests, from
this DUART, are enabled.
Note:
Those interrupts which have been masked out by the IMR are
still disabled. However, if this input is at a logic “l(fā)ow”, then all
interrupts (whether masked or unmasked) are disabled.
Hence, IEI can act to globally disable all DUART interrupt
requests.
IEO - Interrupt Enable Output
This active-high output is only available if the DUART is
configured to operate in the Z-Mode. This output is often
times connected to the IEI input of another (lower priority)
device. This output is “high” if all of the following
conditions are true.
D
The device’s IEI input is at a logic “high”
D
The device is not requesting an interrupt from the
CPU
D
An interrupt, requested by the device, has just been
serviced
If any of these conditions are false, then the IEO pin will be
at a logic “l(fā)ow”.
Note
:
Once the IEO pin has toggled “l(fā)ow”, and the CPU has ac-
knowledged the interrupt request and has completed the inter-
rupt service routine, the IEO pin will remain “l(fā)ow” until the user
invokes the “RESET IUS” command (see Table 3). Therefore,
if the DUART is going to operate in the Z-Mode, the user must
include the “RESET IUS” Command at the very end of the
DUART interrupt service routine.
System Level Application of the IEI and IEO pins
Figure 15 depicts a series of DUARTs connected in a
daisy-chain fashion. In this figure, the left-most DUART
has the highest interrupt priority. This is because this
DUART’s IEI input is hardwired to Vcc. Therefore, the
unmasked interrupt requests, from this DUART are
always enabled. The DUART device, located just to the
right of the “highest interrupt priority” device is of a lower
interrupt priority. This is because the IEI input of this lower
priority device is connected to the IEO output of the
highest priority DUART. Whenever the “highest priority”
device requests an interrupt, its IEO output will toggle
“l(fā)ow”. This will in turn, disable the “l(fā)ower priority” device
相關PDF資料
PDF描述
XR16M2550IM48-F IC UART FIFO 16B 1.8V DL 48TQFP
ST16C552CJ68-F IC UART FIFO PAR 16B DUAL 68PLCC
XR16L2752IJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
XR88C92IJ-F IC UART FIFO DUAL 44PLCC
相關代理商/技術參數
參數描述
XR88C681CJTR-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CN/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*