參數資料
型號： XR88C681CJ-F
廠商： Exar Corporation
文件頁數： 87/101頁
文件大?。?/td> 0K
描述： IC UART CMOS DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1327-5
XR88C681
86
Rev. 2.11
An Address Byte, however, interrupts all “Slaves” so that
each can examine the received byte to test if it (the
individual slave device) is being addressed. The receiver
of the addressed slave will be enabled and will prepare for
reception of the data bytes that follows. The slaves that
were not addressed will leaves their Receivers disabled,
and will continue to ignore the data bytes that follows.
They will be interrupted again when the next address byte
is transmitted by the “Master Device”.
H.2.2 DUART Multi-Drop Operation
A given channel, within the DUART is programmed into
the Multi-Drop mode by setting MR1n[4:3] = “1, 1”. In this
mode, a transmitted character consists of a START bit,
the programmed number of data bits, the Address/Data
(A/D) flag bit; and the programmed STOP bit length. A/D
= 0 indicates that the character is data, while A/D = 1
identifies it as an address.
Transmitter Operation During Multi-Drop Mode
The user/CPU controls the state of the transmitted
character by programming MR1n[2] of the channel prior
to loading the data bits into the THR. Setting MR1n[2] =
“0” results in A/D = “0” and setting MR1n[2] = “1” results in
A/D = “1”.
Figure 48 presents a procedural flow diagram
for transmitting characters (Address or Data), while in the
Multi-Drop Mode.
START
Invoke the “RESET MR
POINTER” command.
(Write 1xh to appropriate
Command Register)
Set A/D Bit to “0”
(Write xxxxx0xx to MR1n
Register)
Transmit Address
Character to Slave Device.
(Write Character to THRn)
Invoke the “RESET MR
POINTER” command.
(Write 1xh to appropriate
Command Register)
Set A/D Bit to “1”
(Write xxxxx1xx to
MR1n Register)
Transmit Data Character
to Slave Device.
(Write Character to THRn)
No
Yes
Figure 48. A Flow Diargam Depicting a Procedure That Can Be Used to
Transmit Characters in the Multi-Drop Mode
Are there More
Data Characters
to Write to Active
Slave Device?
相關PDF資料
PDF描述
XR16M2550IM48-F IC UART FIFO 16B 1.8V DL 48TQFP
ST16C552CJ68-F IC UART FIFO PAR 16B DUAL 68PLCC
XR16L2752IJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
XR88C92IJ-F IC UART FIFO DUAL 44PLCC
相關代理商/技術參數
參數描述
XR88C681CJTR-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CN/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*