參數資料
型號： XR88C681CJ-F
廠商： Exar Corporation
文件頁數： 76/101頁
文件大小： 0K
描述： IC UART CMOS DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1327-5
XR88C681
76
Rev. 2.11
RXDn
Receive Holding
Register
Receive Shift Register
Transmit Shift Register
Transmit Holding
Register
TXCn
TXDn
Incoming
Serial Data
Outgoing
Serial Data
RXCn
Note:
The CPU has no access to the Serial Data during Remote Loopback Mode.
Figure 41. A Block Diagram Depicting Remote Loopback Mode
In this mode:
1. Received data is transmitted on the channel’s TXDn
output
2. Received data is not sent to the CPU and the error
status conditions are not checked.
3. Parity and framing (stop bits) are transmitted as
received.
4. The receiver must be enabled.
5. The received break is echoed as received until the
next valid start bit is detected.
MR2n[5] - Transmitter Request-to-Send Control
Ordinarily, the RTS (Request to Send) output is asserted
or negated by invoking the “SET OUTPUT PORT BITS
COMMAND” or “CLEAR OUTPUT PORT BITS
COMMAND” in the appropriate manner, by the system
software. However, setting MR2n[5] = 1 allows the
Channel Transmitter to negate RTS automatically, one bit
time after the characters in the TSR and THR have been
transmitted and are now empty.
Figure 44 presents a diagram illustrate how a
Transmitter-Controlled Request-to-Send configuration
would function.
MR2n[4] - Clear to Send Control
If this bit is a 0, the channels -CTSn input (IP0 for Channel
A, or IP1 for Channel B) has no effect on the transmitter. If
the bit is a “1”, the transmitter will check the state of its
-CTSn input each time is it ready to send a character. If
-CTSn is low (or “true”), the character is transmitted. If
-CTSn is high (or negated), TXDn remains in the marking
state and the transmission of the next character is
delayed until -CTSn goes low. Changes in the -CTSn
input while a character is being serialized do not affect
transmission of that character. This phenomenon is
further illustrated in
Figure 42 and Figure 44.
相關PDF資料
PDF描述
XR16M2550IM48-F IC UART FIFO 16B 1.8V DL 48TQFP
ST16C552CJ68-F IC UART FIFO PAR 16B DUAL 68PLCC
XR16L2752IJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
XR88C92IJ-F IC UART FIFO DUAL 44PLCC
相關代理商/技術參數
參數描述
XR88C681CJTR-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CN/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*