參數資料
型號： XR88C681CJ-F
廠商： Exar Corporation
文件頁數： 70/101頁
文件大小： 0K
描述： IC UART CMOS DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1327-5
XR88C681
70
Rev. 2.11
Receive Shift Register
RXDn
Incoming
Serial Data
Receive Holding
Register
RXCn
Receiver Clock (from Timing Block)
To Data Bus
To be read by the CPU
Figure 37. A Simplified Drawing of the Receiver Shift Register
and Receiver Holding Register
The receiver functions by sensing the voltage level at the
RXDn input. When the far-end transmitter is idle, its TXDn
output (and consequently, the RXDn input) is
continuously “marking”. During this period the Receiver is
inactive and is not receiving or processing any data.
However, when the far-end transmitter sends the START
bit, (with its TXDn output toggling “l(fā)ow”), a receiver clock,
which is 16 times the baud rate (with the 16x clock), will
start sampling this START bit. If the receiver determines
that its RXDn input is still “l(fā)ow” after its 7th sample, then
the receiver hardware considers this signal to be a valid
START bit. If the RXDn input is not “l(fā)ow” at the 7th
sample, the Receiver will ignore this downward pulse as
“noise”. From this 7th sample on, the Receiver will
sample each successive bit at one bit-period intervals
(1/baud rate) with the 1x clock. The purpose of this 16x
Clock is then two-fold.
1. To verify that the detected “l(fā)ow” level in the RXDn input
is indeed a START bit.
2. To establish the phase relationship between the 1x bit
sampling clock, and the incoming serial data stream.
The idea is to sample each data bit in the middle of its
bit period.
Please note that if a 16X clock is selected for the receiver,
this over-sampling procedure occurs with each and every
start bit.
The receiver will continue to sample (and receive) each
bit of the character that follows the START bit, at one-bit
time intervals. Upon reception of the character’s MSB the
receiver will check parity (if programmed) or will sample
for the STOP bit. If the Receiver samples a mark
condition at this time and the parity check (if any) was
valid; a successful reception of the character is
presumed; and the Receiver will prepare to sense and
oversample the occurrence of the START bit for the next
character.
相關PDF資料
PDF描述
XR16M2550IM48-F IC UART FIFO 16B 1.8V DL 48TQFP
ST16C552CJ68-F IC UART FIFO PAR 16B DUAL 68PLCC
XR16L2752IJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
XR88C92IJ-F IC UART FIFO DUAL 44PLCC
相關代理商/技術參數
參數描述
XR88C681CJTR-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CN/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*