- 您現在的位置：買賣IC網 > PDF目錄3763 > XR88C681CJ-F (Exar Corporation)IC UART CMOS DUAL 44PLCC PDF資料下載
參數資料
| 型號： | XR88C681CJ-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 63/101頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART CMOS DUAL 44PLCC |
| 標準包裝： | 27 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 1 字節，3 字節 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 帶并行端口： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
| 其它名稱： | 1016-1327-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁當前第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
XR88C681
64
Rev. 2.11
In order to enable the “Input Port Change of State” interrupt, one must do the following.
D
Write the appropriate data to the lower nibble of ACR. The bit formats for ACR is presented in
Table 23. Please
note that the applicable bits, within the ACR register, are shaded.
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
BRG Set
Select
Counter/Timer Mode and Source
Delta IP3
Interrupt
Delta IP2
Interrupt
Delta IP1
Interrupt
Delta IP0
Interrupt
0 = Set1
1 = Set2
See
0 = OFF
1 = ON
0 = OFF
1 = ON
0 = OFF
1 = ON
0 = OFF
1 = ON
Table 23. ACR- Auxiliary Control Register
D
Setting IMR[7].
Note:
This “two-tiered” interrupt enabling/disabling approach, for the “Input Change of State” interrupt allows tremendous flexibility
for the user. Setting or clearing the bits in ACR[3:0] allows the user to specify exactly which Input Port pins to be enabled (or
disabled) for generating the “Input Port Change of State” interrupt. Setting or clearing IMR[7] allows the user to “globally”
enable or disable this interrupt.
The upper nibble of the IPCR will indicate which of the four
input pins experienced the “Change of State.” The lower
nibble of the IPCR contains the present state of these
input pins.
Therefore, when reading the IPCR, in
response to the “Change of State” interrupt, the CPU will
determine:
D
The input pin(s) that toggled.
D
The final state of the changing input pin.
E.3 28 Pin Packaged DUARTs
The 28 pin packaged DUARTs come with only one input
port pin, IP2. Therefore, the only alternative functions that
are available to the device (via this input port pin) are
CT_EX (C/T External Clock Input) and RXCB (External
Clock input for Receiver Channel B).
F. OUTPUT PORT
The DUART consists of an 8 bit parallel Output Port. The
Output Port can be used as a general purpose output or
can be used for output timing and status signals by
appropriately programming of the mode registers (MR1A,
B and MR2A, B) and also the output port configuration
register, OPCR. When used to output status signals the
Output Port pins are open drain, which allows their use in
a wire OR interrupt scheme.
Programming the Output Port is a little different from the
conventional writes to a typical parallel port or the data
bus. The Output Port circuitry consists of the Output Port
Register (OPR), and the output port pins themselves.
The contents of the OPR are complements of the actual
state of the Output Port pins.
For Example:
If the bit OPR[5] is set to a logic “1”, this will result in the
OP5 pin being at a logic “0”. Likewise, if the bit OPR[5] is
set to a logic “0”, this results in the OP5 pin being at a logic
“1”. The other thing that makes programming the parallel
port a little odd is the procedure that one must use to
accomplish this feat. When writing to this parallel output
port, one must invoke one of the two address triggered
commands: SET OUTPUT PORT BITS and CLEAR
OUTPUT PORT BITS.
It is important to note that when
invoking the “SET OUTPUT PORT BITS” command, the
user is setting the bits (to logic “1”) in the OPR. However,
this action results in setting the corresponding Output
Port pins to logic “0”; due to the complementary
relationship between the state of the Output Port pins and
the bits in the OPR. Likewise, when the CLEAR OUTPUT
PORT BITS command is invoked, the specified bits,
within the OPR are “cleared” to logic “0”. However, the
corresponding Output Port pins are set to the logic “1”
state.
The state of each bit within the OPR, following a Power-on
Reset (POR), is all “0”. Therefore, the state of each
Output Port pin, following a POR is logic “1”.
The bits of the OPR can be set and cleared individually. A
bit is set by the address-triggered “SET OUTPUT PORT
BITS” command (see
Table 1) with the accompanying
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M2550IM48-F | IC UART FIFO 16B 1.8V DL 48TQFP |
| ST16C552CJ68-F | IC UART FIFO PAR 16B DUAL 68PLCC |
| XR16L2752IJ-F | IC UART FIFO 64B DUAL 44PLCC |
| ST16C552IJ68-F | IC UART FIFO 16B DUAL 68PLCC |
| XR88C92IJ-F | IC UART FIFO DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR88C681CJTR-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C681CN/40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART) |
| XR88C681CP/28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART) |
| XR88C681CP/28-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C681CP/40 | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。