參數資料
型號： XR88C681CJ-F
廠商： Exar Corporation
文件頁數： 64/101頁
文件大?。?/td> 0K
描述： IC UART CMOS DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1327-5
XR88C681
65
Rev. 2.11
data, at the Data Bus, specifying the bits, within the OPR,
to be set ( 1 = set, 0 = no change). A bit is cleared by the
address triggered “CLEAR OUTPUT PORT BITS”
command (see
Table 1) with the accompanying data, at
the Data Bus, specifying the bits to be reset (1 = cleared, 0
= no change).
F.1 Writing Data to the OPR/Output Port Pins
As mentioned earlier, the state of the OPR and
consequently, the Output Port pins is controlled by two
“Address Triggered” commands.
D
Set Output Port Bits Command
D
Clear Output Port Bits Command
The procedure and effect of using these commands are
discussed in
Section F.1.1.
F.1.1 Set Ouput Port Bits Command
The actual procedure used to invoke the “SET OUTPUT
PORT BITS” command is the same as writing the
contents on the Data Bus (D7 - D0) to DUART Address
0E16 for (OP7 - OP0). For every “1” that exists within the
latched contents of the Data Bus, the corresponding bit,
within the OPR is set to a logic “high”. For every “0” that is
present on the data bus and is written to DUART Address
0E16, the state of the corresponding bit, within the OPR is
unchanged.
We could state this another way as: For every “1” that is
present on the Data Bus, during the use of the “SET
OUTPUT PORT BITS” command, the corresponding
Output Port pin is set to a logic “l(fā)ow”. And for every “0” that
is present on the Data Bus, during this command, the
state of the corresponding Output Port pin is unchanged.
For Example:
Suppose that the content of the OPR are OPR[7:0] = [0, 0,
0, 0, 1, 1, 1, 1]. Hence, the state of the Output Port pins
are as follows:
[OP7, OP6, OP5, OP4, OP3, OP2, OP1, OP0] = [1, 1, 1, 1,
0, 0, 0, 0]
If we write the following to DUART Address 0E16;
[D7,...,D0] = [1, 1, 1, 1, 0, 0, 0, 0]; the resulting state of the
Output Port Register Bits follows:
OPR[7:0] = [1, 1, 1, 1, 1, 1, 1, 1].
Consequently, the state of the Output Port pins are as
follows:
[OP7, OP6, OP5, OP4, OP3, OP2, OP1, OP0] = [0, 0, 0, 0,
0, 0, 0, 0]
This example of the “SET OUTPUT PORT BITS”
command is illustrated in
Figure 33.
State of Output Port Pins (OP7 - OP0)
Initial OPR[7:0]
Final OPR[7:0]
Data Bus, D7 - D0
Figure 33. Illustration of the “SET OUTPUT PORT BIT” Command and its Effect
on the Output Port Register and the State of the Output Port Pins.
DUART Address 0Eh
1
0
相關PDF資料
PDF描述
XR16M2550IM48-F IC UART FIFO 16B 1.8V DL 48TQFP
ST16C552CJ68-F IC UART FIFO PAR 16B DUAL 68PLCC
XR16L2752IJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
XR88C92IJ-F IC UART FIFO DUAL 44PLCC
相關代理商/技術參數
參數描述
XR88C681CJTR-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CN/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*