參數資料
型號： 29PL256N
廠商： Spansion Inc.
英文描述： 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
中文描述： 256/128/128字節（16/8/8 M中的x 16位），3.0伏的CMOS只同步讀/寫，頁模式閃存
文件頁數： 25/74頁
文件大小： 1968K
代理商： 29PL256N
June 6, 2007 S29PL-N_00_A5
S29PL-N MirrorBit
Flash Family
25
D a t a
S h e e t
( P r e l i m i n a r y )
7.4
Program/Erase Operations
These devices are capable of single word or write buffer programming operations which are described in the
following sections. The write buffer programming is recommended over single word programming as it has
clear benefits from greater programming efficiency. See
Table 7.1 on page 20
for the correct device settings
required before initiation of a write command sequence.
Note the following details regarding the program/erase operations:
When the Embedded Program algorithm is complete, the device then returns to the read mode.
The system can determine the status of the program operation by using DQ7 or DQ6. See
Write Operation
Status
on page 37
for information on these status bits.
A
0
cannot be programmed back to a
1
. Attempting to do so causes the device to set DQ5 = 1 (halting any
further operation and requiring a reset command). A succeeding read shows that the data is still
0
.
Only erase operations can convert a
0
to a
1
.
A hardware reset immediately terminates the program operation and the program command sequence
should be reinitiated once the device has returned to the read mode, to ensure data integrity.
Any commands written to the device during the Embedded Program Algorithm are ignored except the
Program Suspend command.
Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program operation is in
progress.
Programming is allowed in any sequence and across sector boundaries for single word programming
operation.
7.4.1
Single Word Programming
In single word programming mode, four Flash command write cycles are used to program an individual Flash
address. While this method is supported by all Spansion devices, in general it is not recommended for
devices that support Write Buffer Programming. See
Table 12.1 on page 66
for the required bus cycles and
Figure 7.1 on page 26
for the flowchart.
When the Embedded Program algorithm is complete, the device then returns to the read mode and
addresses are no longer latched. The system can determine the status of the program operation by using
DQ7 or DQ6. See
Write Operation Status
on page 37
for information on these status bits.
Single word programming is supported for backward compatibility with existing Flash driver software and use
of write buffer programming is strongly recommended for general programming. The effective word
programming time using write buffer programming is approximately four times faster than the single word
programming time.
相關PDF資料
PDF描述
29PS 25PS, 42PS, 44PS, 45PS and 46PS Series Pressure Switches
29SL800CB-90 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY
29SL800CT-90 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY
29U194A The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
29U194ADFE The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
相關代理商/技術參數
參數描述
29PN 制造商:APEM 功能描述:
29PP100-2 制造商:SPD 功能描述:
29PP113-1 制造商:SOURIAU 功能描述:JEWELRY CLASS
29PP123-1 制造商:SPD 功能描述:
29PP123-3 制造商:SPD 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*