- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C970AKC (ADVANCED MICRO DEVICES INC) PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product PDF資料下載
參數資料
| 型號： | AM79C970AKC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| 中文描述： | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP13 |
| 封裝： | CARRIER RING, PLASTIC, QFP-132 |
| 文件頁數： | 77/219頁 |
| 文件大?。?/td> | 1065K |
| 代理商： | AM79C970AKC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁當前第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁
P R E L I M I N A R Y
AMD
77
Am79C970A
current descriptor. The OWN bit(s) in the subsequent
descriptor(s) will be cleared until the STP (the next
frame) is found.
Loss of Carrier
When operating in half-duplex mode, a loss of carrier
condition will be reported if the PCnet-PCI II controller
cannot observe receive activity whilst it is transmitting
on the AUI or GPSI port. In AUI mode, after the
PCnet-PCI II controller initiates a transmission it will ex-
pect to see data “l(fā)ooped-back” on the DI
±
pair. This will
internally generate a “carrier sense”, indicating that the
integrity of the data path to and from the MAU is intact,
and that the MAU is operating correctly. This “carrier
sense” signal must be asserted before the last bit is
transmitted on DO
±
. If “carrier sense” does not become
active in response to the data transmission, or becomes
inactive before the end of transmission, the loss of car-
rier (LCAR) error bit will be set in TMD2 after the frame
has been transmitted. The frame will not be retried on
the basis of an LCAR error. In GPSI mode, LCAR will
be asserted if RXEN does not go active during
the transmission.
When the 10BASE-T port is selected, LCAR will be re-
ported for every frame transmitted while the network in-
terface is in the Link Fail state.
Late Collision
A late collision will be reported if a collision condition oc-
curs after one slot time (512 bit times) after the transmit
process was initiated (first bit of preamble commenced).
The PCnet-PCI II controller will abandon the transmit
process for that frame, set Late Collision (LCOL) in the
associated TMD2, and process the next transmit frame
in the ring. Frames experiencing a late collision will not
be retried. Recovery from this condition must be per-
formed by upper layer software.
SQE Test Error
During the inter packet gap time following the comple-
tion of a transmitted message, the AUI CI
±
pair is as-
serted by some transceivers as a self-test. The integral
Manchester Encoder/Decoder will expect the SQE Test
Message (nominal 10 MHz sequence) to be returned via
the CI
±
pair within a 40 network bit-time period after DI
±
goes inactive (this does not apply if the 10BASE-T port
is selected). If the CI
±
input is not asserted within the 40
network bit-time period following the completion of
transmission, then the PCnet-PCI II controller will set
the CERR bit in CSR0. In GPSI mode, CLSN must be
asserted after the transmission or otherwise CERR will
be set. CERR will be asserted in 10BASE-T mode after
transmit if T-MAU is in Link Fail state. CERR will never
cause
INTA
to be activated. It will, however, set the ERR
bit CSR0.
Receive Operation
The receive operation and features of the PCnet-PCI II
controller are controlled by programmable options. The
PCnet-PCI II controller offers a 256-byte receive FIFO
to provide frame buffering for increased system latency,
automatic flushing of collision fragments (runt packets),
automatic receive pad stripping and a variety of address
match options.
Receive Function Programming
Automatic pad field stripping is enabled by setting the
ASTRP_RCV bit in CSR4. This can provide flexibility
in the reception of messages using the 802.3
frame format.
All receive frames can be accepted by setting the PROM
bit in CSR15. Acceptance of unicast and broadcast
frames can be individually turned off by setting the
DRCVPA or DRCVBC bits in CSR15. The Physical Ad-
dress register (CSR12 to CSR14) stores the address
the PCnet-PCI II controller compares to the destination
address of the incoming frame for a unicast address
match. The Logical Address Filter register (CSR8 to
CSR11) serves as a hash filter for multicast
address match.
The point at which the BMU will start to transfer data
from the receive FIFO to buffer memory is controlled by
the RCVFW bits in CSR80. The default established dur-
ing H_RESET is 01b which sets the watermark flag at 64
bytes filled.
For test purposes, the PCnet-PCI II controller can be
programmed to accept runt packets by setting RPA
in CSR124.
Address Matching
The PCnet-PCI II controller supports three types of ad-
dress matching: unicast, multicast, and broadcast. The
normal address matching procedure can be modified by
programming three bits in CSR15, the mode register
(PROM, DRCVPA, and DRCVBC).
If the first bit received after the start of frame delimiter
(the least significant bit of the first byte of the destination
address field) is 0, the frame is unicast, which indicates
that the frame is meant to be received by a single node.
If the first bit received is 1, the frame is multicast, which
indicates that the frame is meant to be received by a
group of nodes. If the destination address field contains
all ONEs, the frame is broadcast, which is a special type
of multicast. Frames with the broadcast address in the
destination address field are meant to be received by all
nodes on the local area network.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C970A | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AVCW | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970 | PCnetTM-PCI Single-Chip Ethernet Controller for PCI Local Bus |
| AM79C971VCW | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
| AM79C971 | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C970AKC\\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Advanced Micro Devices 功能描述: |
| AM79C970AKC\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C970AKCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AVC | 制造商:Advanced Micro Devices 功能描述: |
| AM79C970AVC\\W | 制造商:Advanced Micro Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。