- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C970AKC (ADVANCED MICRO DEVICES INC) PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product PDF資料下載
參數資料
| 型號： | AM79C970AKC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| 中文描述： | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP13 |
| 封裝： | CARRIER RING, PLASTIC, QFP-132 |
| 文件頁數： | 93/219頁 |
| 文件大小： | 1065K |
| 代理商： | AM79C970AKC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁當前第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁
P R E L I M I N A R Y
AMD
93
Am79C970A
register to a value that prevents the PCnet-PCI II
controller from claiming any memory cycles not in-
tended for it.
The Expansion ROM interface uses some of the same
pins as the GPSI interface. Simultaneous use of both
functions is not possible. Reading from the Expansion
ROM and then reconfiguring the pins to the GPSI mode
is supported. An external transceiver is required to pre-
vent contention between the GPSI signals and the data
outputs from the Expansion ROM.
EROE
can be used
as control signal for the external transceiver.
After an H_RESET all pins are internally configured to
function as Expansion ROM interface. When the GPSI
interface is selected by setting PORTSEL (CSR15, bits
8–7) to 10b, the PCnet-PCI II controller will terminate
all further read accesses to Expansion ROM by assert-
ing
TRDY
within two clock cycles. The read data will
be undefined.
During the boot procedure the system will try to find an
Expansion ROM. A PCI system assumes that an
Expansion ROM is present when it reads the ROM sig-
nature 55h (byte 0) and AAh (byte 1). A design without
Expansion ROM can guarantee that the Expansion
ROM detection fails by connecting two adjacent ERD
pins together and tying them high or low.
EEPROM Microwire Interface
The PCnet-PCI II controller contains a built-in capability
for reading and writing to an external serial EEPROM.
This built-in capability consists of an interface for direct
connection to a Microwire compatible EEPROM, an
automatic EEPROM read feature, and a user-program-
mable register that allows direct access to the Microwire
interface pins.
Automatic EEPROM Read Operation
Shortly after the deassertion of the
RST
pin, the
PCnet-PCI II controller will read the contents of the
EEPROM that is attached to the Microwire interface.
Because of this automaticread capability of the PCnet-
PCI II controller, an EEPROM can be used to program
many of the features of the PCnet-PCI II controller at
power-up, allowing system-dependent configuration in-
formation to be stored in the hardware, instead of inside
the device driver.
If an EEPROM exists on the Microwire interface, the
PCnet-PCI II controller will read the EEPROM contents
at the end of the H_RESET operation. The EEPROM
contents will be serially shifted into a temporary register
and then sent to various register locations on board the
PCnet-PCI II controller. Access to the PCnet-PCI II con-
troller configuration space, the Expansion ROM or any
I/O resource is not possible during the EEPROM read
operation. The PCnet-PCI II controller will terminate any
access attempt with the assertion of
DEVSEL
and
STOP
while
TRDY
is not asserted, signaling to the initia-
tor to disconnect and retry the access at a later time.
A checksum verification is performed on the data that is
read from the EEPROM. If the checksum verification
passes, PVALID (BCR19, bit 15) will be set to ONE. If
the checksum verification of the EEPROM data fails,
PVALID will be cleared to ZERO and the PCnet-PCI II
controller will force all EEPROM-programmable BCR
registers back to their H_RESET default values. The
content of the Address PROM locations (offsets 0h–Fh
from the I/O or memory mapped I/O base address),
however, will not be cleared. The 8 bit checksum for the
entire 36 bytes of the EEPROM should be FFh.
If no EEPROM is present at the time of the automatic
read operation, the PCnet-PCI II controller will recog-
nize this condition and will abort the automatic read op-
eration and clear both the PREAD and PVALID bits in
BCR19. All EEPROM-programmable BCR registers will
be assigned their default values after H_RESET. The
content of the Address PROM locations (offsets 0h–Fh
from the I/O or memory mapped I/O base address) will
be undefined.
If the user wishes to modify any of the configuration bits
that are contained in the EEPROM, then the seven com-
mand, data and status bits of BCR19 can be used to
write to the EEPROM. After writing to the EEPROM, the
host should set the PREAD bit of BCR19. This action
forces a PCnet-PCI II controller re-read of the EEPROM
so that the new EEPROM contents will be loaded into
the EEPROM-programmable registers on board the
PCnet-PCI II controller. (The EEPROM-programmable
registers may also be reprogrammed directly, but only
information that is stored in the EEPROM will be pre-
served at system power-down.) When the PREAD bit of
BCR19 is set, it will cause the PCnet-PCI II controller to
ignore further accesses to the PCnet-PCI II controller
configuration space, the Expansion ROM, or any I/O re-
source until the completion of the EEPROM read opera-
tion. The PCnet-PCI II controller will terminate these
access attempts with the assertion of
DEVSEL
and
STOP
while
TRDY
is not asserted, signaling to the initia-
tor to disconnect and retry the access at a
later time.
EEPROM Auto-Detection
The PCnet-PCI II controller uses the EESK/
LED1
/SFBD
pin to determine if an EEPROM is present in the system.
At the rising edge of CLK during the last clock during
which
RST
is asserted, the PCnet-PCI II controller will
sample the value of the EESK/
LED1
/SFBD pin. If the
sampled value is a ONE, then the PCnet-PCI II control-
ler assumes that an EEPROM is present, and the
EEPROM read operation begins shortly after the
RST
pin is deasserted. If the sampled value of
EESK/
LED1
/SFBD is a ZERO, the PCnet-PCI II
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C970A | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AVCW | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970 | PCnetTM-PCI Single-Chip Ethernet Controller for PCI Local Bus |
| AM79C971VCW | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
| AM79C971 | PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C970AKC\\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Advanced Micro Devices 功能描述: |
| AM79C970AKC\W | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM79C970AKCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AVC | 制造商:Advanced Micro Devices 功能描述: |
| AM79C970AVC\\W | 制造商:Advanced Micro Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。