- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCT5VJE7Y Microcontroller PDF資料下載
參數資料
| 型號： | CR16HCT5VJE7Y |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 76/157頁 |
| 文件大?。?/td> | 1256K |
| 代理商： | CR16HCT5VJE7Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁當前第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
76
UnPSEL
Parity Select. This 2-bit field selects parity type
as follows:
00 = odd parity
01 = even parity
10 = mark (0)
11 = space (1)
When the USART is configured to transmit nine
data bits per frame, the parity bit is omitted and
the UnPSEL field is ignored.
Parity Enable. This bit enables (1) or disables
(0) parity bit generation and parity checking.
When the USART is configured to transmit nine
data bits per frame, there is no parity bit and the
UnPEN bit is ignored.
UnPEN
18.3.6
The USART Mode Select Register is a byte-wide, read/write
register that selects the clock source, synchronization mode,
attention mode, and line break generation. This register is
cleared upon reset. When the software writes to this register,
the reserved bits must be cleared to 0 for proper operation.
The register format is shown below.
7
6
5
4
3
Reserved
UnCKS
UnBRK
USART Mode Select Register (UnMDSL)
UnMOD
Mode of Operation. Set to 0 for asynchronous
operation or 1 for synchronous operation.
Attention Mode. When set to 1, this bit selects
the attention mode of operation for the USART.
When cleared to 0, the attention mode is dis-
abled. The hardware clears this bit after an ad-
dress frame is received. An address frame is a
9-bit character with a 1 in the ninth bit position.
Force Transmission Break. Setting this bit to 1
causes the TDXn pin to go low. TDXn remains
low until the UnBRK bit is cleared to 0 by the
software.
Synchronous Clock Source. This bit controls
the clock source when the USART operates in
the synchronous mode (UnMOD=1). If the
UnCKS bit is set to 1, the USART operates
from an external clock provided on the CKXn
pin. If the UnCKS bit is cleared to 0, the USART
operates from the baud rate clock produced by
the USART on the CKXn pin. This bit is ignored
when the USART operates in the asynchro-
nous mode.
UnATN
UnBRK
UnCKS
18.3.7
The USART Status Register is a byte-wide, read-only regis-
ter that contains the receive and transmit status bits. This
register is cleared upon reset. Any attempt by the software to
write to this register is ignored. The register format is shown
below.
USART Status Register (UnSTAT)
UnPE
Parity Error. This bit is set to 1 when a parity er-
ror is detected within a received character. This
bit is automatically cleared to 0 by the hard-
ware when the UnSTAT register is read.
Framing Error. This bit is set to 1 when the US-
ART fails to receive a valid stop bit at the end
of a frame. This bit is automatically cleared to 0
by the hardware when the UnSTAT register is
read.
Data Overrun Error. This bit is set to 1 when a
new character is received and transferred to
the UnBUF register before the software has
read the previous character from UnBUF. This
bit is automatically cleared to 0 by the hard-
ware when the UnSTAT register is read.
Error Status Flag. This bit is set when a parity,
framing, or overrun error occurs (any time that
the UnPE, UnFE, or UnDOE bit is set). It is au-
tomatically cleared to 0 by the hardware when
the UnPE, UnFE, and UnDOE bits are all 0.
Break Detect. This bit is set to 1 when a line
break condition occurs. This condition is de-
tected if RDXn remains low for at least ten bit
times after a missing stop bit has been detect-
ed at the end of a frame.
The hardware automatically clears the UnBKD
bit upon read of the UnSTAT register, but only
if the break condition on RXDn no longer exists.
If reading the UnSTAT register does not clear
the UnBKD bit because the break is still active-
ly driven on the line, the hardware clears the bit
as soon as the break condition no longer exists
(when RXDn returns to a high level).
Received 9th Data Bit. With the USART config-
ured to operate in the 9-bit data format, this is
equal to the ninth data bit of the last frame re-
ceived.
Transmit In Progress. The hardware sets this
bit to 1 when the USART is transmitting data
and clears it to 0 at the end of the last frame bit.
UnFE
UnDOE
UnERR
UnBKD
UnRB9
UnXMIP
18.3.8
The USART Interrupt Control Register is a byte-wide register
that contains the receive and transmit interrupt status flags
(read-only bits) and the interrupt enable bits (read/write bits).
The register is set to 01 hex upon reset. The register format
is shown below.
7
6
5
4
UnEEI
UnERI
UnETI
Reserved
USART Interrupt Control Register (UnICTRL)
UnTBE
Transmit Buffer Empty. This read-only bit is set
to 1 by the hardware when the USART trans-
fers data from the UnTBUF register to the
transmit shift register for transmission. It is au-
tomatically cleared to 0 by the hardware on the
next write to the UnTBUF register.
Receive Buffer Full. This read-only bit is set by
the hardware when the USART has received a
complete data frame and has transferred the
data from the receive shift register to the UnR-
BUF register. It is automatically cleared to 0 by
the hardware when the UnRBUF register is
read.
UnRBF
2
1
0
UnATN
UnMOD
7
6
5
4
3
2
1
0
Reserved UnXMIP
UnRB9
UnBKD
UnERR
UnDOE
UnFE
UnPE
3
2
1
0
UnRBF
UnTBE
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT5VJE8Y | Microcontroller |
| CR16HCT5VJE9Y | Microcontroller |
| CR16HCT9 | |
| CR16HCT9VJE7 | Microcontroller |
| CR16HCT9VJE7Y | Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCT5VJE8Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT5VJE9Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT5VJEXY | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9VJE7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。