參數資料
型號: DS3112+
廠商: Maxim Integrated Products
文件頁數: 80/133頁
文件大?。?/td> 0K
描述: IC MUX TEMPE T3/E3 256-BGA
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 40
控制器類型: 調幀器,多路復用器
接口: 并行/串行
電源電壓: 3.135 V ~ 3.465 V
電流 - 電源: 150mA
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 256-LBGA
供應商設備封裝: 256-PBGA(27x27)
包裝: 管件
產品目錄頁面: 1419 (CN2011-ZH PDF)
DS3112
50 of 133
Bit 7: T3/E3 Diagnostic Loopback Enable (DLB). See Figure 1-1 and Figure 1-2 for a visual description of this
loopback.
0 = disable loopback
1 = enable loopback
Bit 8: E3 Code Violation Enable (E3CVE). This bit is ignored in the T3 mode. This bit is used in the E3 mode to
configure the BiPolar Violation Count Register (BPVCR) to count either BiPolar Violations (BPV) or Code
Violations (CV). A BPV is defined as consecutive pulses (or marks) of the same polarity that are not part of a
HDB3 codeword. A CV is defined in ITU O.161 as consecutive BPVs of the same polarity.
0 = count BPV
1 = count CV
Bits 9 and 10: T3/E3 Frame Error Counting Control Bits 0 and 1 (FECC0 and FECC1).
FECC1
FECC0
FRAME ERROR COUNT REGISTER (FECR) CONFIGURATION
0
T3 Mode: Count Loss Of Frame (LOF) Occurrences
E3 Mode: Count Loss Of Frame (LOF) Occurrences
0
1
T3 Mode: Count Both F Bit and M Bit Errors
E3 Mode: Count Bit Errors in the FAS Word
1
0
T3 Mode: Count Only F Bit Errors
E3 Mode: Count Word Errors in the FAS Word
1
T3 Mode: Count Only M Bit Errors
E3 Mode: Illegal State
Bit 11: Error Counting Control (ECC). This bit is used to control whether the device will increment the error
counters during Loss Of Frame (LOF) conditions. It only affects the error counters that count errors that are based
on framed information and these include the following:
Frame Error Counter (when it is configured to count frame errors, not LOF occurrences)
T3 Parity Bit Error Counter
T3 C-Bit Parity Error Counter
T3 Far End Block Error or E3 RAI Counter
When this bit is set low, these error counters will not be allowed to increment during LOF conditions. When this bit
is set high, these error counters will be allowed to increment during LOF conditions.
0 = stop the FECR/PCR/CPCR/FEBECR error counters from incrementing during LOF
1 = allow the FECR/PCR/CPCR/FEBECR error counters to increment during LOF
Bit 12: Automatic FEBE Defeat (AFEBED). This bit is ignored in the E3 mode and in the T3 mode when the
device is not configured in the C-Bit Parity Mode. When this bit is low, the device will automatically insert the
FEBE codes into the transmitted data stream by setting all three C bits in Subframe 4 to zero.
0 = automatically insert FEBE codes in the transmit data stream based on detected errors
1 = use the TFEBE control to determine the state of the FEBE codes
Bit 13: Transmit FEBE Setting (TFEBE). This bit is only active when AFEBED is active (i.e., AFEBED = 1).
When this bit is low, the device will force the FEBE code to 111 continuously. When this bit is set high, the device
will force the FEBE code to 000 continuously.
0 = force FEBE to 111 (null state)
1 = force FEBE to 000 (active state)
Bit 14: T3/E3 Payload Loopback Enable (PLB). See Figure 1-1 and Figure 1-2 for a visual description of this
loopback.
0 = disable loopback
1 = enable loopback
相關PDF資料
PDF描述
PIC16F1847-E/P MCU 14KB FLASH 1KB RAM 18PDIP
DS21Q43AT+ IC FRAMER E1 QUAD 5V IND 128TQFP
PIC16LF1847-E/P MCU 14KB FLASH 1KB RAM 18PDIP
DS21Q43AT IC FRAMER E1 QUAD 5V IND 128TQFP
DS2143Q IC CONTROLLER E1 5V LP 44-PLCC
相關代理商/技術參數
參數描述
DS3112+ 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112+W 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112D1 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112D1+ 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3112DK 功能描述:網絡開發工具 DS3112 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V