- 您現在的位置：買賣IC網 > PDF目錄17111 > EVAL-ADUC832QSZ (Analog Devices Inc)KIT DEV FOR ADUC832 QUICK START PDF資料下載
參數資料
| 型號： | EVAL-ADUC832QSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 57/92頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT DEV FOR ADUC832 QUICK START |
| 產品培訓模塊： | Process Control |
| 標準包裝： | 1 |
| 系列： | QuickStart™ 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC832 |
| 所含物品： | 評估板，線纜，電源，軟件和文檔 |
| 其它名稱： | EVAL-ADUC832QS EVAL-ADUC832QS-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
ADuC832
Data Sheet
Rev. B | Page 60 of 92
I2C-COMPATIBLE INTERFACE
The ADuC832 supports a fully licensed I2C serial interface. The
I2C interface is implemented as a full hardware slave and soft-
ware master. SDATA is the data I/O pin and SCLOCK is the
serial clock. These two pins are shared with the MOSI and
SCLOCK pins of the on-chip SPI interface. Therefore, the user
can only enable one interface or the other at any given time
(see SPE in SPICON in Table 28). The uC001 Technical Note,
MicroConverter I2C Compatible Interface, describes the opera-
tion of this interface as implemented, and is available from the
MicroConverter website at www.analog.com/microconverter.
I2C INTERFACE SFRs
Three SFRs are used to control the I2C interface. These are
described in the following sections.
I2CCON (I2Control Register)
SFR Address:
E8H
Power-On Default Value:
00H
Bit Addressable:
Yes
I2CADD (I2C Address Register)
SFR Address:
9BH
Power-On Default Value:
55H
Bit Addressable:
No
The I2CADD SFR holds the I2C peripheral address for the part.
It can be overwritten by user code. Technical Note uC001 at
www.analog.com/microconverter describes the format of the
I2C standard 7-bit address in detail.
I2CDAT (I2C Data Register)
SFR Address:
9AH
Power-On Default Value:
00H
Bit Addressable:
No
The I2CDAT SFR is written by the user to transmit data over
the I2C interface or read by user code to read data just received
by the I2C interface. Accessing I2CDAT automatically clears any
pending I2C interrupt and the I2CI bit in the I2CCON SFR. User
software should only access I2CDAT once per interrupt cycle.
Table 29. I2CCON SFR Bit Designations
Bit
Name
Description
[7]
MDO
I2C software master data output bit (master mode only). This data bit is used to implement a master I2C transmitter interface
in software. Data written to this bit is output on the SDATA pin if the data output enable (MDE) bit is set.
[6]
MDE
I2C software master data output enable bit (master mode only). Set by user to enable the SDATA pin as an output (Tx).
Cleared by the user to enable SDATA pin as an input (Rx).
[5]
MCO
I2C software master clock output bit (master mode only). This data bit is used to implement a master I2C transmitter interface
in software. Data written to this bit is output on the SCLOCK pin.
[4]
MDI
I2C software master data input bit (master mode only). This data bit is used to implement a master I2C receiver interface in
software. Data on the SDATA pin is latched into this bit on SCLOCK if the data output enable (MDE) bit is 0.
[3]
I2CM
I2C master/slave mode bit set by user to enable I2C software master mode. Cleared by user to enable I2C hardware slave
mode.
[2]
I2CRS
I2C reset bit (slave mode only). Set by user to reset the I2C interface. Cleared by user code for normal I2C operation.
[1]
I2CTX
I2C direction transfer bit (slave mode only). Set by the MicroConverter if the interface is transmitting. Cleared by the
MicroConverter if the interface is receiving.
[0]
I2CI
I2C interrupt bit (slave mode only). Set by the MicroConverter after a byte has been transmitted or received. Cleared
automatically when user code reads the I2CDAT SFR (see the I2CADD (I2C Address Register) section).
相關PDF資料 |
PDF描述 |
|---|---|
| HBM15DRXS | CONN EDGECARD 30POS DIP .156 SLD |
| PCX1H270MCL1GS | CAP ALUM 27UF 50V 20% SMD |
| HSM08DRKI | CONN EDGECARD 16POS DIP .156 SLD |
| 0210490857 | CABLE JUMPER 1.25MM .051M 17POS |
| EVAL-ADUC831QSZ | KIT DEV FOR ADUC831 QUICK START |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC834QS | 制造商:Analog Devices 功能描述:DATA ACQ SYS, MICROCNVRTR, DUAL 16BIT/24BIT - ADCS W/ EMBEDD - Bulk 制造商:Analog Devices 功能描述:8052 ADUC834 QUICKSTART DEV KIT |
| EVAL-ADUC834QSZ | 功能描述:KIT DEV QUICK START ADUC834 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| EVAL-ADUC836QS | 制造商:Analog Devices 功能描述:MCU 8BIT 8052 CISC 62KB+4KB FLASH 3.6V 48LQFP - Bulk 制造商:Analog Devices 功能描述:KIT- ADUC836 DEV SYSTEM |
| EVAL-ADUC841QS | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| EVAL-ADUC841QSP2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
發布緊急采購，3分鐘左右您將得到回復。