參數資料
型號： EVAL-ADV7393EBZ
廠商： Analog Devices Inc
文件頁數： 62/108頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR ADV7393 ENCODER
標準包裝： 1
系列： Advantiv®
主要目的： 視頻，視頻編碼器
已用 IC / 零件： ADV7393
已供物品： 板
相關產品： ADV7393BCPZ-ND - IC DAC VIDEO HDTV 10BIT 40LFCSP
ADV7393BCPZ-REEL-ND - IC DAC ENCODER VID HDTV 40-LFCSP
Data Sheet
ADV7390/ADV7391/ADV7392/ADV7393
Rev. G | Page 57 of 108
SD LUMA AND COLOR SCALE CONTROL
Subaddress 0x9C to Subaddress 0x9F
When enabled, the SD luma and color scale control feature can
be used to scale the SD Y, Cb, and Cr output levels. This feature
can be enabled using Subaddress 0x87, Bit 0. This feature affects
all SD output signals, that is, CVBS, Y-C, YPrPb, and RGB.
When enabled, three 10-bit registers (SD Y scale, SD Cb scale,
and SD Cr scale) control the scaling of the SD Y, Cb, and Cr
output levels. The SD Y scale register contains the scaling factor
used to scale the Y level from 0.0 to 1.5 times its initial level.
The SD Cb scale and SD Cr scale registers contain the scaling
factors to scale the Cb and Cr levels from 0.0 to 2.0 times their
initial levels, respectively.
The values to be written to these 10-bit registers are calculated
using the following equation:
Y, Cb, or Cr Scale Value = Scale Factor × 512
For example, if Scale Factor = 1.3
Y, Cb, or Cr Scale Value = 1.3 × 512 = 665.6
Y, Cb, or Cr Scale Value = 666 (rounded to the nearest integer)
Y, Cb, or Cr Scale Value = 1010011010b
Subaddress 0x9C, SD scale LSB = 0x2A
Subaddress 0x9D, SD Y scale register = 0xA6
Subaddress 0x9E, SD Cb scale register = 0xA6
Subaddress 0x9F, SD Cr scale register = 0xA6
It is recommended that the SD luma scale saturation feature
(Subaddress 0x87, Bit 1) be enabled when scaling the Y output
level to avoid excessive Y output levels.
SD HUE ADJUST CONTROL
Subaddress 0xA0
When enabled, the SD hue adjust control register (Subaddress
0xA0) is used to adjust the hue on the SD composite and
chroma outputs. This feature can be enabled using Subaddress
0x87, Bit 2.
Subaddress 0xA0 contains the bits required to vary the hue of
the video data, that is, the variance in phase of the subcarrier
during active video with respect to the phase of the subcarrier
during the color burst. The ADV739x provides a range of
±22.5° in increments of 0.17578125°. For normal operation
(zero adjustment), this register is set to 0x80. Value 0xFF and
Value 0x00 represent the upper and lower limits, respectively, of
the attainable adjustment in NTSC mode. Value 0xFF and Value
0x01 represent the upper and lower limits, respectively, of the
attainable adjustment in PAL mode.
The hue adjust value is calculated using the following equation:
Hue Adjust (°) = 0.17578125° (HCRd 128)
Where HCRd = the hue adjust control register (decimal).
For example, to adjust the hue by +4°, write 0x97 to the hue
adjust control register.
97
x
0
151
128
17578125
.
0
4
=
≈
+
d
where the sum is rounded to the nearest integer.
To adjust the hue by 4°, write 0x69 to the hue adjust control
register.
9
6
x
0
105
128
17578125
.
0
4
=
≈
+
d
where the sum is rounded to the nearest integer.
SD BRIGHTNESS DETECT
Subaddress 0xBA
The ADV739x allows monitoring of the brightness level of the
incoming video data. This feature is used to monitor the
average brightness of the incoming Y signal on a field-by-field
basis. The information is read from the I2C and, based on this
information, the color saturation, contrast, and brightness
controls can be adjusted (for example, to compensate for very
dark pictures).
The luma data is monitored in the active video area only. The
average brightness I2C register is updated on the falling edge of
every VSYNC signal. The SD brightness detect register (Subad-
dress 0xBA) is a read-only register.
SD BRIGHTNESS CONTROL
Subaddress 0xA1, Bits[6:0]
When this feature is enabled, the SD brightness/WSS control
register (Subaddress 0xA1) is used to control brightness by
adding a programmable setup level onto the scaled Y data. This
feature can be enabled using Subaddress 0x87, Bit 3.
For NTSC with pedestal, the setup can vary from 0 IRE to 22.5 IRE.
For NTSC without pedestal (see Figure 69) and for PAL, the
setup can vary from 7.5 IRE to +15 IRE.
Figure 69. Examples of Brightness Control Values
The SD brightness control register is an 8-bit register. The seven
LSBs of this 8-bit register are used to control the brightness
level, which can be a positive or negative value.
For example, to add a +20 IRE brightness level to an NTSC
signal with pedestal, write 0x28 to Subaddress 0xA1.
0 × (SD Brightness Value) =
0 × (IRE Value × 2.015631) =
0 × (20 × 2.015631) = 0 × (40.31262) ≈ 0x28
NTSC WITHOUT PEDESTAL
NO SETUP
VALUE ADDED
POSITIVE SETUP
VALUE ADDED
100 IRE
0 IRE
NEGATIVE SETUP
VALUE ADDED
–7.5 IRE
+7.5 IRE
06234-
070
相關PDF資料
PDF描述
AK672M/2-3-R CABLE MINI USB 5PIN 3M 2.0 VERS
AK669-18-BLACK-R CABLE USB 1.1 A-A M-F BLACK 1.8M
H3AKH-1436G IDC CABLE - HSC14H/AE14G/HPK14H
EET-UQ2C152DA CAP ALUM 1500UF 160V 20% SNAP
ADP195-EVALZ BOARD EVALUATION FOR ADP195
相關代理商/技術參數
參數描述
EVAL-ADV739XFEZ 功能描述:BOARD EVAL FOR ADV739XFEZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-ADV7400AEBM 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit Intergrated Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer
EVAL-ADV7400EBM 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-ADV7400EBM-U2 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-ADV7401EB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*