參數資料
型號： ICS1892Y-10
英文描述： 10Base-T/100Base-TX Integrated PHYceiver
文件頁數： 19/148頁
文件大?。?/td> 816K
代理商： ICS1892Y-10
Chapter 5
Operating Modes Overview
ICS1892, Rev. D, 2/26/01
February 26, 2001
19
ICS1892
2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
5.1.2
Specific Reset Operations
This section discusses the following specific ways that the ICS1892 can be reset:
Hardware reset (using the RESET* pin)
Power-on reset (applying power to the ICS1892)
Software reset (using Control Register bit 0.15)
Note:
At the completion of a reset (either hardware, power-on, or software), the ICS1892 sets all
registers to their default values.
5.1.2.1
Hardware Reset
Entering Hardware Reset
Holding the active-low RESET* pin low for a minimum of five REF_IN clock cycles initiates a hardware
reset (that is, the ICS1892 enters the reset state). During reset, the ICS1892 executes the steps listed in
Section 5.1.1.1, “Entering Reset”
.
Exiting Hardware Reset
After the signal on the RESET* pin transitions from a low to a high state, the ICS1892 completes in 640 ns
(that is, in 16 REF_IN clocks) steps 1 through 5, listed in
Section 5.1.1.2, “Exiting Reset”
. After the first five
steps are completed, the Serial Management Port is ready for normal operations, but this action does not
signify the end of the reset cycle. The reset cycle completes when the transmit clock (TXCLK) and receive
clock (RXCLK) are available, which is typically 53 ms after the RESET* pin goes high. [For details on this
transition, see
Section 10.5.17, “Reset: Hardware Reset and Power-Down”
.]
Note:
1.
2.
The MAC/Repeater Interface is not available for use until the TXCLK and RXCLK are valid.
The Control Register bit 0.15 does not represent the status of a hardware reset. It is a self-clearing bit
that is used to initiate a software reset.
5.1.2.2
Power-On Reset
Entering Power-On Reset
When power is applied to the ICS1892, it waits until the potential between V
DD
and V
SS
achieves a
minimum voltage of 4.5 VDC before entering reset and executing the steps listed in
Section 5.1.1.1,
“Entering Reset”
. After entering reset from a power-on condition, the ICS1892 remains in reset for
approximately 20
μ
s. (For details on this transition, see
Section 10.5.16, “Reset: Power-On Reset”
.)
Exiting Power-On Reset
The ICS1892 automatically exits reset and performs the same steps as for a hardware reset. (See
Section
5.1.1.2, “Exiting Reset”
.)
Note:
The only difference between a hardware reset and a power-on reset is that during a power-on
reset, the ICS1892 isolates the RESET* input pin. All other functionality is the same. As with a
hardware reset, the Control Register bit 0.15 does not represent the status of a power-on reset.
相關PDF資料
PDF描述
ICS1892Y-14 10Base-T/100Base-TX Integrated PHYceiver
ICS1893AF 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM
ICS1893Y-10 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM
ICS1893 3.3-V 10Base-T/100Base-TX Integrated PHYceiver⑩
ICS2002 Wavedec Digital Audio Codec
相關代理商/技術參數
參數描述
ICS1892Y-14 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver
ICS1893 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver
ICS1893_09 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver?
ICS1893AF 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
ICS1893AFI 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*