- 您現在的位置：買賣IC網 > PDF目錄360744 > ICS1892Y 10Base-T/100Base-TX Integrated PHYceiver PDF資料下載
參數資料
| 型號： | ICS1892Y |
| 英文描述： | 10Base-T/100Base-TX Integrated PHYceiver |
| 文件頁數： | 50/148頁 |
| 文件大?。?/td> | 816K |
| 代理商： | ICS1892Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
ICS1892, Rev. D, 2/26/01
February 26, 2001
50
Chapter 7
Functional Blocks
ICS1892 Data Sheet
2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
7.5.4
10Base-T Operation: Idle
The ICS1892 10Base-T Idle Function transmits link pulses in the absence of data (that is, when the
MAC/repeater is not requiring it to transmit any data). During this time the link is Idle, and the 10Base-T Idle
Function begins periodically transmitting link pulses at a rate of one pulse every 16 ms, as defined in the
ISO/IEC 8802-3 standard. In 10Base-T mode, the ICS1892 transmits link pulses whenever the
MAC/repeater does not have any data available for transmission. The ICS1892 continues transmitting link
pulses while receiving data. Because link pulses indicate an idle state for a link, this situation does not
generate a Collision Detect signal (COL).
7.5.5
10Base-T Operation: Link Monitor
When the ICS1892 is in 10Base-T mode, the Link Monitor Function observes the data received by the
10Base-T Twisted-Pair Receiver to determine the link status. The results of this continual monitoring are
stored in the Link Status bit. The Station Management entity (STA) can access the Link Status bit in either
the Status Register (bit 1.2) or the QuickPoll Detailed Status Register (bit 17.0). This Link Status bit is a
latching low (LL) bit. (For more information on latching high and latching low bits, see
Section 8.1.4.1,
“Latching High Bits”
and
Section 8.1.4.2, “Latching Low Bits”
.)
The STA can control the execution of the Smart Squelch Function using bit 18.0 (the Smart Squelch Inhibit
bit in the 10Base-T Operations Register). The Squelch Inhibit bit allows an STA to control the ICS1892
Squelch Detection in 10Base-T mode. When an STA sets this bit to logic:
Zero, before the ICS1892 can establish a valid link, the ICS1892 must receive valid 10Base-T data.
One, before the ICS1892 can establish a valid link, the ICS1892 must receive both valid 10Base-T data
followed by an IDL.
The criteria used by the Link Monitoring Function to declare a link either valid (that is, ‘established’ or ‘up’)
or invalid (that is, ‘failed’ or ‘down’) depends upon the present state of the link and the incoming data. When
the 10Base-T link is:
Valid, the Link Monitor Function continues to report the link as valid as long as it detects either data or
Normal Link Pulses (NLPs) on its Twisted-Pair Receiver. If the 10Base-T Operations Register’s Smart
Squelch Inhibit bit (bit 18.0) is:
– Enabled, before the 10Base-T link can be valid, there must be an IDL at the end of a data packet.
– Disabled, before the 10Base-T link can be valid, all that is needed is a data packet.
Invalid, the Link Monitor Function must detect one of three events before transitioning the link from the
invalid state to the valid state. If the ICS1892 receives any of the following it changes the status of the
link from invalid to valid:
– More than seven Normal Link Pulses (NLPs)
– Any data
– Any data followed by a valid IDL
The ICS1892 receives data when the Twisted-Pair Receiver phase-locked loop can acquire lock and
extract the receive clock from the incoming data stream for three bit times.
If the ICS1892 receives neither data nor NLPs (that is, the link shows either no activity or inconsistent
activity) for more than 81 to 83 ms, then the ICS1892 declares the link invalid and sets the LL Link Status
bit to logic zero. The LL Link Status bit remains latched in the cleared state until a reset occurs or until
the STA reads it while the link is valid.
Note:
1.
When the link is invalid and the ICS1892 detects the presence of data, the ICS1892
does not transition
the link to the valid state until after the reception of the present packet is complete.
Enabling or disabling the Smart Squelch Function affects the Link Monitor function.
A transition from the invalid state to the valid state does not automatically update the LL Link Status bit.
2.
3.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS1892Y-10 | 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1892Y-14 | 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1893AF | 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM |
| ICS1893Y-10 | 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM |
| ICS1893 | 3.3-V 10Base-T/100Base-TX Integrated PHYceiver⑩ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS1892Y-10 | 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver |
| ICS1892Y-14 | 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver |
| ICS1893 | 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1893_09 | 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver? |
| ICS1893AF | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。