參數資料
型號： ICS1892Y
英文描述： 10Base-T/100Base-TX Integrated PHYceiver
文件頁數： 63/148頁
文件大?。?/td> 816K
代理商： ICS1892Y
Chapter 8
Management Register Set
ICS1892, Rev. D, 2/26/01
February 26, 2001
63
ICS1892
2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
8.2.2
Loopback Enable (bit 0.14)
This bit controls the Loopback mode for the ICS1892. Setting this bit to logic:
Zero disables the Loopback mode.
One enables the Loopback mode by disabling the Twisted-Pair Transmitter, the Twisted-Pair Receiver,
and the collision detection circuitry. (The STA can override the ICS1892 from disabling the collision
detection circuitry in Loopback mode by writing logic one to bit 0.7.)
When the ICS1892 is in Loopback
mode, the data presented at the MAC/repeater transmit interface is internally looped back to the
MAC/repeater receive interface. The delay from the assertion of Transmit Data Enable (TXEN) to the
assertion of Receive Data valid (RXDV) is less than 512 bit times.
8.2.3
Data Rate Select (bit 0.13)
This bit provides a means of controlling the ICS1892 data rate. Its operation depends on the state of
several other functions, including the HW/SW input pin and the Auto-Negotiation Enable bit (bit 0.12).
When the ICS1892 is configured for:
Hardware mode (that is, the HW/SW pin is logic zero), the ICS1892 isolates this bit 0.13 and uses the
10/100SEL input pin to establish the data rate for the ICS1892. In this Hardware mode:
– Bit 0.13 is undefined.
– The ICS1892 provides a Data Rate Status bit (in the QuickPoll Detailed Status Register, bit 17.15),
which always shows the setting of an active link.
Software mode (that is, the HW/SW pin is logic one), the function of bit 0.13 depends on the
Auto-Negotiation Enable bit 0.12. When Auto-Negotiation is:
– Enabled, the ICS1892 isolates bit 0.13 and relies on the results of the auto-negotiation process to
establish the data rate.
– Disabled, bit 0.13 determines the data rate. In this case, setting bit 0.13 to logic:
Zero selects 10-Mbps ICS1892 operations.
One selects 100-Mbps ICS1892 operations.
8.2.4
Auto-Negotiation Enable (bit 0.12)
This bit provides a means of controlling the ICS1892 Auto-Negotiation sublayer. Its operation depends on
the HW/SW input pin.
When the ICS1892 is configured for:
Hardware mode, (that is, the HW/SW pin is logic zero), the ICS1892 isolates bit 0.12 and uses the
ANSEL (Auto-Negotiation Select) input pin to determine whether to enable the Auto-Negotiation
sublayer.
Note:
Software mode, (that is, the HW/SW pin is logic one), bit 0.12 determines whether to enable the
Auto-Negotiation sublayer. When bit 0.12 is logic:
– Zero:
The ICS1892 disables the Auto-Negotiation sublayer.
The ICS1892 bit 0.13 (the Data Rate bit) and bit 0.8 (the Duplex Mode bit) determine the data rate
and the duplex mode.
– One:
The ICS1892 enables the Auto-Negotiation sublayer.
The ICS1892 isolates bit 0.13 and bit 0.8.
In Hardware mode, bit 0.12 is undefined.
相關PDF資料
PDF描述
ICS1892Y-10 10Base-T/100Base-TX Integrated PHYceiver
ICS1892Y-14 10Base-T/100Base-TX Integrated PHYceiver
ICS1893AF 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM
ICS1893Y-10 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM
ICS1893 3.3-V 10Base-T/100Base-TX Integrated PHYceiver⑩
相關代理商/技術參數
參數描述
ICS1892Y-10 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver
ICS1892Y-14 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver
ICS1893 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver
ICS1893_09 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver?
ICS1893AF 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*