參數資料
型號： KSZ8851SNLI TR
廠商： Micrel Inc
文件頁數： 7/80頁
文件大?。?/td> 0K
描述： IC ETHERNET CTLR 1PORT PCI 32MLF
標準包裝： 1
控制器類型： 以太網控制器，MAC/PHY
接口： 總線
電源電壓： 1.8V，2.5V，3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，32-MLF?
供應商設備封裝： 32-MLF?（5x5）
包裝： 標準包裝
產品目錄頁面： 1081 (CN2011-ZH PDF)
其它名稱： 576-3506-6
Micrel, Inc.
KSZ8851SNL/SNLI
August 2009
15
M9999-083109-2.0
Wake-up Packet
Wake-up packets are certain types of packets with specific CRC values that a system recognizes as a ‘wake up’ frame.
The KSZ8851SNL supports up to four users defined wake-up frames as below:
1. Wake-up frame 0 is defined in wakeup frame registers (0x30 – 0x3B) and is enabled by bit 0 in wakeup frame control
register (0x2A).
2. Wake-up frame 1 is defined in wakeup frame registers (0x40 – 0x4B) and is enabled by bit 1 in wakeup frame control
register (0x2A).
3. Wake-up frame 2 is defined in wakeup frame registers (0x50 – 0x5B) and is enabled by bit 2 in wakeup frame control
register (0x2A).
4. Wake-up frame 3 is defined in wakeup frame registers (0x60 – 0x6B) and is enabled by bit 3 in wakeup frame control
register (0x2A).
Magic Packet
Magic Packet technology is used to remotely wake up a sleeping or powered off PC on a LAN. This is accomplished by
sending a specific packet of information, called a Magic Packet frame, to a node on the network. When a PC capable of
receiving the specific frame goes to sleep, it enables the Magic Packet RX mode in the LAN controller, and when the LAN
controller receives a Magic Packet frame, it will alert the system to wake up.
Magic Packet is a standard feature integrated into the KSZ8851SNL. The controller implements multiple advanced power-
down modes including Magic Packet to conserve power and operate more efficiently.
Once the KSZ8851SNL has been put into Magic Packet Enable mode (WFCR[7]=1), it scans all incoming frames
addressed to the node for a specific data sequence, which indicates to the controller this is a Magic Packet (MP) frame.
A Magic Packet frame must also meet the basic requirements for the LAN technology chosen, such as Source Address
(SA), Destination Address (DA), which may be the receiving station’s IEEE address or a multicast or broadcast address
and CRC.
The specific sequence consists of 16 duplications of the IEEE address of this node, with no breaks or interruptions. This
sequence can be located anywhere within the packet, but must be preceded by a synchronization stream. The
synchronization stream allows the scanning state machine to be much simpler. The synchronization stream is defined as
6 bytes of FFh. The device will also accept a broadcast frame, as long as the 16 duplications of the IEEE address match
the address of the machine to be awakened.
Example:
If the IEEE address for a particular node on a network is 11h 22h, 33h, 44h, 55h, 66h, the LAN controller would be
scanning for the data sequence (assuming an Ethernet frame):
DESTINATION SOURCE – MISC - FF FF FF FF FF FF - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 -
11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 - 11 22 33 44 55 66 -
11 22 33 44 55 66 - MISC - CRC.
There are no further restrictions on a Magic Packet frame. For instance, the sequence could be in a TCP/IP packet or an
IPX packet. The frame may be bridged or routed across the network without affecting its ability to wake-up a node at the
frame’s destination.
If the LAN controller scans a frame and does not find the specific sequence shown above, it discards the frame and takes
no further action. If the KSZ8851SNL controller detects the data sequence, however, it then alerts the PC’s power
management circuitry (assert the PME pin) to wake up the system.
相關PDF資料
PDF描述
KSZ8862-16MQL IC SWITCH 10/100 16BIT 128-PQFP
KSZ8862-32MQL IC ETHERNET SW 2PORT BUS 128PQFP
KSZ8863MLLI IC ETHERNET SWITCH 3PORT 48-LQFP
KSZ8864RMNI IC ETHERNET SWITCH 4PORT 64QFN
KSZ8873FLLI IC ETHERNET SWITCH 3PORT 64LQFP
相關代理商/技術參數
參數描述
KSZ8851SNLTR 制造商:Micrel Inc 功能描述:
KSZ8851SNL-TR 功能描述:Ethernet Controller 10/100 Base-T/TX PHY SPI Interface 32-MLF? (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 協議:以太網 功能:控制器 接口:SPI 標準:10/100 Base-T/TX PHY 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:- 工作溫度:0°C ~ 70°C 封裝/外殼:32-VFQFN 裸露焊盤，32-MLF? 供應商器件封裝:32-MLF?（5x5） 標準包裝:1
KSZ8852HLE-EVAL 功能描述:KSZ8852HLE - Interface, Ethernet Control Evaluation Board 制造商:microchip technology 系列:- 零件狀態:有效 主要用途:接口，以太網控制 嵌入式:否 使用的 IC/零件:KSZ8852HLE 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1
KSZ8852HLEWA 功能描述:Ethernet Switch 10/100 Base-FX/T/TX PHY Ethernet Interface 64-LQFP (10x10) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:以太網 標準:10/100 Base-FX/T/TX PHY 電壓 - 電源:3.3V 電流 - 電源:- 工作溫度:-40°C ~ 115°C 封裝/外殼:64-LQFP 裸露焊盤 供應商器件封裝:64-LQFP（10x10） 標準包裝:160
KSZ8852HLEYA 功能描述:Ethernet Switch 10/100 Base-FX/T/TX PHY Ethernet Interface 64-LQFP (10x10) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:以太網 標準:10/100 Base-FX/T/TX PHY 電壓 - 電源:3.3V 電流 - 電源:- 工作溫度:-40°C ~ 115°C 封裝/外殼:64-LQFP 裸露焊盤 供應商器件封裝:64-LQFP（10x10） 標準包裝:160
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*