參數資料
型號： MCIMX514AJM6C
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： SPECIALTY MICROPROCESSOR CIRCUIT, PBGA529
封裝： 19 X 19 MM, 0.8 MM PITCH, ROHS COMPLIANT, BGA-529
文件頁數： 24/172頁
文件大?。?/td> 2218K
代理商： MCIMX514AJM6C
i.MX51A Automotive and Infotainment Applications Processors, Rev. 4
12
Freescale Semiconductor
Features
GPIO_NAND
This is a general-purpose input/output (GPIO3_12) on the NVCC_NANDF_A power rail.
IOB, IOG, IOR,
IOB_BACK, IOG_BACK,
and IOR_BACK
These signals are analog TV outputs that should be tied to GND when not being used.
JTAG_nnnn
The JTAG interface is summarized in Table 4. Use of external resistors is unnecessary. However,
if external resistors are used, the user must ensure that the on-chip pull-up/down configuration is
followed. For example, do not use an external pull down on an input that has on-chip pull-up.
JTAG_TDO is configured with a keeper circuit such that the floating condition is eliminated if an
external pull resistor is not present. An external pull resistor on JTAG_TDO is detrimental and
should be avoided.
JTAG_MOD is referenced as SJC_MOD in the i.MX51 Multimedia Applications Processor
Reference Manual (MCIMX51RM). Both names refer to the same signal. JTAG_MOD must be
externally connected to GND for normal operation. Termination to GND through an external
pull-down resistor (such as 1 k
Ω) is allowed.
NC
These signals are No Connect (NC) and should be floated by the user.
PMIC_INT_REQ
When using the MC13892 power management IC, the PMIC_INT_REQ high-priority interrupt input
on i.MX51 should be either floated or tied to NVCC_SRTC_POW with a 4.7 k
Ω to 68 kΩ resistor.
This avoids a continuous current drain on the real-time clock backup battery due to a 100 k
Ω
on-chip pull-up resistor.
PMIC_INT_REQ is not used by the Freescale BSP (board support package) software. The BSP
requires that the general-purpose INT output from the MC13892 be connected to the i.MX51 GPIO
input GPIO1_8 configured to cause an interrupt that is not high-priority.
The original intent was for PMIC_INT_REQ to be connected to a circuit that detects when the
battery is almost depleted. In this case, the I/O must be configured as alternate mode 0 (ALT0 =
power fail).
POR_B
This cold reset negative logic input resets all modules and logic in the IC.
Note: The POR_B input must be immediately asserted at power-up and remain asserted until
after the last power rail is at its working voltage.
RESET_IN_B
This warm reset negative logic input resets all modules and logic except for the following:
Test logic (JTAG, IOMUXC, DAP)
SRTC
Memory repair – Configuration of memory repair per fuse settings
Cold reset logic of WDOG – Some WDOG logic is only reset by POR_B. See WDOG chapter
in i.MX51 Multimedia Applications Processor Reference Manual (MCIMX51RM) for details.
RREFEXT
Determines the reference current for the USB PHY bandgap reference. An external 6.04 k
Ω 1%
resistor to GND is required.
SGND, SVCC, and
SVDDGP
These sense lines provide the ability to sense actual on-chip voltage levels on their respective
supplies. SGND monitors differentials of the on-chip ground versus an external power source.
SVCC monitors on-chip VCC, and SVDDGP monitors VDDGP. Freescale recommends
connection of the SVCC and SVDDGP signals to the feedback inputs of switching power-supplies
or to test points.
STR
This signal is reserved for Freescale manufacturing use. The user should float this signal.
TEST_MODE
TEST_MODE is for Freescale factory use only. This signal is internally connected to an on-chip
pull-down device. Users must either float this signal or tie it to GND.
Table 3. Special Signal Considerations (continued)
Signal Name
Remarks
相關PDF資料
PDF描述
MCIMX537CVV8C 32-BIT, 800 MHz, RISC PROCESSOR, PBGA529
MCM16Y1BACFT16 16-BIT, MROM, MICROCONTROLLER, PQFP160
MCM16Y1BGCFT16 16-BIT, MROM, MICROCONTROLLER, PQFP160
M68HC16Y1CFC 16-BIT, MROM, MICROCONTROLLER, PQFP16
MCV14AI/SL 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO14
相關代理商/技術參數
參數描述
MCIMX514AJM6CR2 制造商:Freescale Semiconductor 功能描述:ELVIS 3.0 AUTO - Tape and Reel
MCIMX515CJM6C 功能描述:處理器 - 專門應用 iMX515 App Processor RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX515CJM6CR2 功能描述:處理器 - 專門應用 i.MX51 32bit 800 MHz RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX515DJM8C 功能描述:處理器 - 專門應用 iMX515 App Processor Extended Temp RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX515DJM8C 制造商:Freescale Semiconductor 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*