![](http://datasheet.mmic.net.cn/330000/PCI4515_datasheet_16443874/PCI4515_147.png)
715
7.21 PCI Miscellaneous Configuration Register
The PCI miscellaneous configuration register provides miscellaneous PCI-related configuration. See Table 719 for
a complete description of the register contents.
Bit
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
Name
PCI miscellaneous configuration
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
PCI miscellaneous configuration
Type
RW
R
RW
R
RW
RW
RW
RW
R
R
R
RW
RW
RW
RW
RW
Default
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
Register:
Offset:
Type:
Default:
PCI miscellaneous configuration
F0h
Read/Write, Read-only
0000 0810h
Table 719. PCI Miscellaneous Configuration Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
3116
RSVD
R
Reserved. Bits 3116 return 0s when read.
15
PME_D3COLD
RW
PME support from D3cold. This bit programs bit 15 (PME_D3COLD) in the power management
capabilities register at offset 46h in the PCI configuration space (see Section 7.17).
1412
RSVD
R
Reserved. Bits 1412 return 0s when read.
11
PCI2_3_EN
RW
PCI 2.3 Enable. The PCI4515 1394 OHCI function always conforms to the PCI 2.3 specification.
Therefore, this bit is tied to 1.
10
ignore_mstrIntEna
_for_pme
RW
Ignore IntMask.msterIntEnable bit for PME generation. When set, this bit causes the PME generation
behavior to be changed as described in Section 3.8. When set, this bit also causes bit 26 of the OHCI
vendor ID register at OHCI offset 40h (see Section 8.15) to read 1; otherwise, bit 26 reads 0.
0 = PME behavior generated from unmasked interrupt bits and IntMask.masterIntEnable bit
(default)
1 = PME generation does not depend on the value of IntMask.masterIntEnable
98
MR_ENHANCE
RW
This field selects the read command behavior of the PCI master for read transactions of greater than
two data phases. For read transactions of one or two data phases, a memory read command is used.
The default of this field is 00. This register is loaded by the serial EEPROM word 12, bits 10.
00 = Memory read line (default)
01 = Memory read
10 = Memory read multiple
11 = Reserved, behavior reverts to default
76
RSVD
R
Reserved. Bits 76 return 0s when read.
5
RSVD
R
Reserved. Bit 5 returns 0 when read.
Bit 4 defaults to 0, which provides OHCI-Lynx
compatible target abort signaling. When this bit is
set to 1, it enables the no-target-abort mode, in which the PCI4515 controller returns indeterminate
data instead of signaling target abort.
The PCI4515 LLC is divided into the PCLK and SCLK domains. If software tries to access registers
in the link that are not active because the SCLK is disabled, then a target abort is issued by the link.
On some systems, this can cause a problem resulting in a fatal system error. Enabling this bit allows
the link to respond to these types of requests by returning FFh.
It is recommended that this bit be set to 1.
4
DIS_TGT_ABT
RW
3
GP2IIC
RW
When bit 3 is set to 1, the GPIO3 and GPIO2 signals are internally routed to the SCL and SDA,
respectively. The GPIO3 and GPIO2 terminals are also placed in the high-impedance state.
2
DISABLE_
SCLKGATE
RW
When bit 2 is set to 1, the internal SCLK runs identically with the chip input. This is a test feature only
and must be cleared to 0 (all applications).