參數資料
型號： PSD813F
廠商： 意法半導體
英文描述： Flash In-System-Programmable Microcontroller Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM)
中文描述： Flash在系統可編程微控制器外圍設備（閃速，在系統可編程微控制器外圍器件，100萬位閃速存儲器，256K位的EEPROM，16K的位的SRAM）
文件頁數： 70/130頁
文件大?。?/td> 650K
代理商： PSD813F
PSD813F Famly
Prelimnary
66
The
PSD813F
Functional
Blocks
(cont.)
9.4.6 Port C – Functionality and Structure
Port C can be configured to perform one or more of the following functions (see Figure 29):
J
MCU I/O Mode
J
CPLD Output – McellBC[7:0] outputs can be connected to Port B or Port C.
J
CPLD Input – via the Input Micro
Cells
J
Address In – Additional high address inputs using the Input Micro
Cells.
J
In-System Programming – JTAG port can be enabled for programming/erase of the
PSD813F device. (See Section 9.6 for more information on JTAG programming.)
J
Open Drain – Port C pins can be configured in Open Drain Mode
J
Battery Backup features – PC2 can be configured as a Battery Input (Vstby) pin.
PC4 can be configured as a Battery On Indicator output
pin, indicating when Vcc is less than Vbat.
Port C does not support Address Out mode, and therefore no Control Register is required.
Pin PC7 may be configured as the DBE input in certain microcontroller interfaces.
9.4.7 Port D – Functionality and Structure
Port D has three I/O pins. See Figure 30. This port does not support Address Out mode,
and therefore no Control Register is required. Port D can be configured to perform one or
more of the following functions:
J
MCU I/O Mode
J
CPLD Output – (external chip select)
J
CPLD Input – direct input to CPLD, no Input Micro
Cells
J
Slew rate – pins can be set up for fast slew rate
Port D pins can be configured in PSDsoft as input pins for other dedicated functions:
J
PD0 – ALE, as address strobe input
J
PD1 – CLKIN, as clock input to the Micro
Cells Flip Flops and APD counter
J
PD2 – CSI, as active low chip select input. A high input will disable the
Flash/EEPROM/SRAM and CSIOP.
9.4.7.1 External Chip Select
The CPLD also provides three chip select outputs on Port D pins that can be used to
select external devices. Each chip select (ECS0-2) consists of one product term that can be
configured active high or low. The output enable of the pin is controlled by either the output
enable product term or the Direction Register. (See Figure 30.)
相關PDF資料
PDF描述
PSD813FH(中文) Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
PSD813FN(中文) Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FN Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FH Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
PSD82 Three Phase Rectifier Bridges
相關代理商/技術參數
參數描述
PSD813F1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash in-system programmable (ISP) peripherals for 8-bit MCUs, 5 V
PSD813F1-A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1A-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F1-A-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*