參數資料
型號： PSD813F
廠商： 意法半導體
英文描述： Flash In-System-Programmable Microcontroller Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM)
中文描述： Flash在系統可編程微控制器外圍設備（閃速，在系統可編程微控制器外圍器件，100萬位閃速存儲器，256K位的EEPROM，16K的位的SRAM）
文件頁數： 82/130頁
文件大?。?/td> 650K
代理商： PSD813F
PSD813F Famly
Prelimnary
78
9.6.1 Standard JTAGSignals (cont.)
The PSD813F supports JTAG In-System-Configuration (ISC) commands, but not Boundary
Scan. A definition of these JTAG-ISC commands and sequences are defined in a
supplemental document available from WSI. WSI’s PSDsoft software tool and FlashLink
JTAG programming cable implement these JTAG-ISC commands. This document is needed
only as a reference for designers who use a FlashLink to program their PSD813F.
9.6.2 JTAGExtensions
TSTAT and TERR are two JTAG extension signals enabled by an “ISC_ENABLE”
command received over the four standard JTAG pins (TMS, TCK, TDI, and TDO). They are
used to speed programming and erase functions by indicating status on PSD pins instead
of having to scan the status out serially using the standard JTAG channel. See Application
Note 54.
TERR will indicate if an error has occurred when erasing a sector or programming a byte in
Flash memory. This signal will go low (active) when an error condition occurs, and stay
low until an “ISC_CLEAR” command is executed or a chip reset pulse is received after an
“ISC-DISABLE” command. TERR does not apply to EEPROM.
TSTAT behaves the same as the Rdy/Bsy signal described in section 9.1.1.2. TSTAT will be
high when the PSD813F device is in read array mode (Flash memory and EEPROM
contents can be read). TSTAT will be low when Flash memory programming or erase cycles
are in progress, and also when data is being written to EEPROM.
TSTAT and TERR can be configured as open-drain type signals during an “ISC_ENABLE”
command. This facilitates a wired-OR connection of TSTAT signals from several PSD813F
devices and a wired-OR connection of TERR signals from those same devices. This is
useful when several PSD813F devices are “chained” together in a JTAG environment.
9.6.3 Security and Flash Memories and EEPROM Protection
When the security bit is set, the device cannot be read on a device programmer or through
the JTAG Port. When using the JTAG Port, only a full chip erase command is allowed.
All other program/erase/verify commands are blocked. Full chip erase returns the part to a
non-secured blank state. The Security Bit can be set in PSDsoft Configuration.
All Flash Memory and EEPROM sectors can individually be sector protected against
erasures. The sector protect bits can be set in PSDsoft Configuration.
The
PSD813F
Functional
Blocks
(cont.)
相關PDF資料
PDF描述
PSD813FH(中文) Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
PSD813FN(中文) Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FN Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FH Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
PSD82 Three Phase Rectifier Bridges
相關代理商/技術參數
參數描述
PSD813F1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash in-system programmable (ISP) peripherals for 8-bit MCUs, 5 V
PSD813F1-A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F1A-12J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V
PSD813F1-A-12JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*