The maximum internal current (I
參數資料
型號： SPAKDSP321VL240
廠商： Freescale Semiconductor
文件頁數： 61/84頁
文件大?。?/td> 0K
描述： IC DSP 24BIT 240MHZ 196-MAPBGA
標準包裝： 2
系列： DSP56K/Symphony
類型： 定點
接口： 主機接口，SSI，SCI
時鐘速率： 240MHz
非易失內存： ROM（576 B）
芯片上RAM： 576kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.60V
工作溫度： -40°C ~ 100°C
安裝類型： 表面貼裝
封裝/外殼： 196-LBGA
供應商設備封裝： 196-MAPBGA（15x15）
包裝： 托盤
DSP56321 Technical Data, Rev. 11
4-4
Freescale Semiconductor
Design Considerations
Equation 4:
The maximum internal current (ICCImax) value reflects the typical possible switching of the internal buses on best-
case operation conditions—not necessarily a real application case. The typical internal current (ICCItyp) value
reflects the average switching of the internal buses on typical operating conditions.
Perform the following steps for applications that require very low current consumption:
1.
Set the EBD bit when you are not accessing external memory.
2.
Minimize external memory accesses, and use internal memory accesses.
3.
Minimize the number of pins that are switching.
4.
Minimize the capacitive load on the pins.
5.
Connect the unused inputs to pull-up or pull-down resistors.
6.
Disable unused peripherals.
7.
Disable unused pin activity (for example, CLKOUT, XTAL).
One way to evaluate power consumption is to use a current-per-MIPS measurement methodology to minimize
specific board effects (that is, to compensate for measured board current not caused by the DSP). A benchmark
power consumption test algorithm is listed in Appendix A. Use the test algorithm, specific test current
measurements, and the following equation to derive the current-per-MIPS value.
Equation 5:
Where:
ItypF2
=
current at F2
ItypF1
=
current at F1
F2
=
high frequency (any specified operating frequency)
F1
=
low frequency (any specified operating frequency lower than F2)
Note:
F1 should be significantly less than F2. For example, F2 could be 66 MHz and F1 could be 33 MHz. The
degree of difference between F1 and F2 determines the amount of precision with which the current rating
can be determined for an application.
4.4 Input (EXTAL) Jitter Requirements
The allowed jitter on the frequency of EXTAL is 0.5 percent. If the rate of change of the frequency of EXTAL is slow
(that is, it does not jump between the minimum and maximum values in one cycle) or the frequency of the jitter is
fast (that is, it does not stay at an extreme value for a long time), then the allowed jitter can be 2 percent. The phase
and frequency jitter performance results are valid only if the input jitter is less than the prescribed values.
I
50
10
12
–
×
3.3
×
33
×
10
6
×
5.48 mA
==
MIPS
I
MHz
I
typF2
I
typF1
–
()
F2
F1
–
()
==
相關PDF資料
PDF描述
VE-B6R-CY-S CONVERTER MOD DC/DC 7.5V 50W
EMC07DRXS CONN EDGECARD 14POS DIP .100 SLD
ACC35DREH-S734 CONN EDGECARD 70POS .100 EYELET
XC5VLX110-1FFG676C IC FPGA VIRTEX-5 110K 676FBGA
VI-BNB-CY-S CONVERTER MOD DC/DC 95V 50W
相關代理商/技術參數
參數描述
SPAKDSP321VL275 功能描述:IC DSP 24BIT 275MHZ 196-MAPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:DSP56K/Symphony 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
SPAKDSP56824BU70 制造商:Freescale Semiconductor 功能描述:
SPAKF56009FJ81 制造商:Motorola Inc 功能描述:
SPAKMC331CFC16 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:User’s Manual
SPAKMC331CFC20 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:User’s Manual
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*