參數資料
型號： TMS320VC5409GGU-80
廠商： Texas Instruments
文件頁數： 32/93頁
文件大?。?/td> 0K
描述： IC FIXED POINT DSP 144-BGA
標準包裝： 160
系列： TMS320C54x
類型： 定點
接口： 主機接口，McBSP
時鐘速率： 80MHz
非易失內存： ROM（32 kB）
芯片上RAM： 64kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.80V
工作溫度： -40°C ~ 100°C
安裝類型： 表面貼裝
封裝/外殼： 144-LFBGA
供應商設備封裝： 144-BGA MICROSTAR（12x12）
包裝： 托盤
配用： 296-15829-ND - DSP STARTER KIT FOR TMS320C5416
Functional Overview
38
April 1999 Revised October 2008
SPRS082F
3.3.5 DMA Controller
The 5409 direct memory access (DMA) controller transfers data between points in the memory map without
intervention by the CPU. The DMA controller allows movements of data to and from internal program/data
memory, internal peripherals (such as the McBSPs), and external program/data memory to occur in the
background of CPU operation. The DMA has six independent programmable channels allowing six different
contexts for DMA operation.
The DMA has the following features:
The DMA has external memory access.
The DMA operates independently of the CPU.
The DMA has six channels. The DMA can keep track of the contexts of six independent block transfers.
The DMA has higher priority than the CPU for internal accesses.
Each channel has independently programmable priorities.
Each channel’s source and destination address registers can have configurable indexes through memory
on each read and write transfer, respectively. The address may remain constant, be post-incremented,
post-decremented, or be adjusted by a programmable value.
Each internal read or write transfer may be initialized by selected sync events.
Each DMA channel is capable of sending interrupts to the CPU.
The DMA can perform double-word transfers (a 32-bit transfer of two 16-bit words). (Internally only)
3.3.5.1
DMA External Access
The 5409 DMA supports external accesses to extended program, extended data, and extended I/O memory.
These overlay pages are only visible to the DMA controller. A maximum of two DMA channels can be used
for external memory accesses. The DMA external accesses require 9 cycle minimums for external writes and
13 cycle minimums for external reads.
The control of the bus is arbitrated between the CPU and the DMA. While the DMA or CPU is in control of the
external bus the other will be heldoff via wait states until the current transfer is complete. The DMA takes
precedence over XIO requests. The HOLD/HOLDA feature of the 5409 affects external CPU transfers as well
as external DMA transfers. When an external processor asserts the HOLD pin to gain control of the memory
interface, the HOLDA signal is not asserted until all pending DMA transfers are complete. To prevent the DMA
from blocking out the CPU or HOLD/HOLDA feature from accessing the external bus, uninterrupted burst
transfers are not supported by the DMA. Subsequently, CPU and DMA arbitration testing is performed for
each external bus cycle, regardless of the bus activity.
Only two channels are available for external accesses. (One for external reads/one for external writes.)
Single-word (16-bit) transfers are supported for external accesses.
The DMA does not support transfers from peripherals to external memory.
The DMA does not support transfers from external memory to the peripherals.
The DMA does not support external to external transfers.
The DMA does not support synchronized external transfers.
The HM bit in the ST1 register indicates whether the processor continues internal execution when
acknowledging an active HOLD signal.
HM = 0, the processor continues execution from internal program memory but places its external interface
in the high impedance state.
HM = 1, the processor halts internal execution.
To ensure that proper arbitration occurs, the HM bit should be set to 0 in the memory-mapped ST1 register.
If the HM is set to 1 the processor will halt during DMA external transfers.
相關PDF資料
PDF描述
HSM06DSXH CONN EDGECARD 12POS DIP .156 SLD
AGM30DRSS CONN EDGECARD 60POS DIP .156 SLD
ACM30DRMT CONN EDGECARD 60POS .156 WW
BWR-5/1700-D12A-C CONV DC/DC +/-5V +/-1700MA DIP
ESC49DRTN-S93 CONN EDGECARD 98POS DIP .100 SLD
相關代理商/技術參數
參數描述
TMS320VC5409PGE100 功能描述:數字信號處理器和控制器 - DSP, DSC Fixed-Pt Dig Sig Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320VC5409PGE100 制造商:Texas Instruments 功能描述:Digital Signal Processor IC
TMS320VC5409PGE-80 功能描述:數字信號處理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320VC5409ZGU100 功能描述:數字信號處理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320VC5409ZGU-80 功能描述:數字信號處理器和控制器 - DSP, DSC Fixed-Pt Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*