- 您現在的位置：買賣IC網 > PDF目錄140358 > W25X10BVSNIG (WINBOND ELECTRONICS CORP) 1M X 1 FLASH 2.7V PROM, PDSO8 PDF資料下載
參數資料
| 型號： | W25X10BVSNIG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 1M X 1 FLASH 2.7V PROM, PDSO8 |
| 封裝： | 0.150 INCH, GREEN, PLASTIC, SOIC-8 |
| 文件頁數： | 22/51頁 |
| 文件大?。?/td> | 1632K |
| 代理商： | W25X10BVSNIG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
W25X10BV/20BV/40BV
Publication Release Date: July 10, 2009
- 29 -
Preliminary -- Revision A
9.2.17
Chip Erase (C7h or 60h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A
Write Enable instruction must be executed before the device will accept the Chip Erase Instruction
(Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and
shifting the instruction code “C7h” or “60h”. The Chip Erase instruction sequence is shown in figure
17.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip
Erase instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction
will commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in
progress, the Read Status Register instruction may still be accessed to check the status of the BUSY
bit. The BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is
ready to accept other instructions again. After the Chip Erase cycle has finished the Write Enable
Latch (WEL) bit in the Status Register is cleared to 0. The Chip Erase instruction will not be executed
if any page is protected by the Block Protect (BP2, BP1, and BP0) bits (see Status Register Memory
Protection table).
Figure 17. Chip Erase Instruction Sequence Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| W3EG6467S403D4SG | 64M X 64 DDR DRAM MODULE, 0.7 ns, DMA200 |
| W7NCF02GH10CSAEG | 128M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF04GH10CSAADM1G | FLASH 3.3V PROM MODULE, XMA50 |
| W7NCF04GH10ISA3FM1G | FLASH 3.3V PROM MODULE, XMA50 |
| W7NCF04GH10ISA9HM1G | FLASH 3.3V PROM MODULE, XMA50 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25X10BVZPIG | 功能描述:IC SPI FLASH 1MBIT 8WSON RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR) |
| W25X10CLSNIG | 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 2.5V/3.3V 1Mbit 128K/64K x 8bit/16bit 8ns 8-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8SOIC |
| W25X10CLSNIG TR | 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 1M-BIT, 4KB UNIFORM 制造商:Winbond Electronics Corp 功能描述:IC MEMORY |
| W25X10CLZPIG | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON |
| W25X10CLZPIG TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON |
發布緊急采購，3分鐘左右您將得到回復。