- 您現在的位置：買賣IC網 > PDF目錄361790 > W66910 PDF資料下載
參數資料
| 型號： | W66910 |
| 文件頁數： | 46/81頁 |
| 文件大?。?/td> | 1058K |
| 代理商： | W66910 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
Data Sheet
W66910 PCI ISDN S/T-Controller
Publication Release Date:
Feb,2001
Revision 1.0
-46 -
Setting this bit activates the D_ch HDLC receiver. This bit can be read. The receiver must be in active state in order to receive
data.
XACTB Transmitter Active
Resetting this bit activates the D_ch HDLC transmitter. This bit can be read. The transmitter must be in active state in order to
transmit data. Note this bit is active LOW.
MFD Multiframe Disable
This bit is used to enable or disable the multiframe structure on S/T interface :
0 : Multiframe is enabled
1 : Multiframe is disabled
DLP Digital Loopback
Setting this bit activates the digital loopback function. The transmitted digital 2B+D channels are looped to the received 2B+D
channels. Note that after hardware reset, the internal clocks will turn off if the S bus is not connected or if there is no signal on
the S bus. In this case, the C/I command ECK must be issued to enable loopback function.
RLP Remote Loopback
Setting this bit to "1" activates the remote loopback function. The received 2B channels from the S interface are looped to the
transmitted 2B channels of S interface. The D channel is not looped in this loopback function.
Bits 7, 4, 3 Reserved
These bits are reserved. The write values are don't care, but are read as zero.
8.1.5 Timer 1 Register
Value after reset : 00H
7
T1MD
CNT6
T1MD Timer1 Mode
0 = Single mode: The timer counts once and generates a T1EXP interrupt when expires.
1 = Periodical mode: The timer counts periodically and generates an interrupt at each expiration.
CNT6-0 Count Value
The expiration time is defined as:
T1 = CNT[6:0] * 0.1 second
TIMR1
Read/Write Address 04H
6
5
4
3
2
1
0
CNT5
CNT4
CNT3
CNT2
CNT1
CNT0
相關PDF資料 |
PDF描述 |
|---|---|
| W6692A | TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
| W6692ACD | ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
| W6692ACF | ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
| W6694A | TE Mode S/T Controller with USB 1.1 Interface |
| W6694CD | USB Bus ISDN S/T-Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W66910CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:TE Mode ISDN S/T-Controller with Microprocessor Interface |
| W6691CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6691CP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6692 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCI Bus ISDN S/T-Controller |
| W6692A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
發布緊急采購，3分鐘左右您將得到回復。