- 您現在的位置：買賣IC網 > PDF目錄361790 > W66910 PDF資料下載
參數資料
| 型號： | W66910 |
| 文件頁數： | 47/81頁 |
| 文件大小： | 1058K |
| 代理商： | W66910 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
Data Sheet
W66910 PCI ISDN S/T-Controller
Publication Release Date:
Feb,2001
Revision 1.0
-47 -
After writing this register, STT1 bit in D_CMDR register must be set to start the timer. This register can be read only after the
timer has been started. The read value indicates the timer's current count value. In case layer 1 is not activated, a C/I command
"ECK" must be issued in addition to the STT1 command to start the timer.
The timer is stopped when it expires (T1MD=0) or TIMR1 register is re-written.
8.1.6 Interrupt Status Register
Value after reset : 00H
7
6
D_RMR
D_RME
D_RMR D_ch Receive Message Ready
A 64-byte data is available in the D_RFIFO. The frame is not complete yet.
D_RME D_ch Receive Message End
The last part of a frame with length > 64 bytes or a whole frame with length
≤
64 bytes has been received. The whole frame
length is obtained from D_RBCH + D_RBCL registers. The length of data in the D_RFIFO equals:
data length = RBC5-0 f RBC5-0
≠
0
data length = 64 f RBC5-0 =0
D_XFR D_ch Transmit FIFO Ready
This bit indicates that the transmit FIFO is ready to accept data. Up to 64 bytes of data can be written into the D_XFIFO.
An D_XFR interrupt is generated in the following cases :
After an XMS command, when
≥
64 bytes of XFIFO is empty
After an XMS together with an XME command is issued, when the whole frame has been transmitted
After an XRST command
After hardware reset
XINT1 XINTIN1 Interrupt
This bit indicates that level change occurs at XINTIN1 pin. Both positive and negative edges will cause an interrupt.
XINT0 XINTIN1 Interrupt
This bit indicates that level change occurs at XINTIN0 pin. Both positive and negative edges will cause an interrupt.
D_EXI D_ch Extended Interrupt
This bit indicates that at least one interrupt bit has been set in D_EXIR register.
B1_EXI B1_ch Extended Interrupt
This bit indicates that at least one interrupt bit has been set in B1_EXIR register.
ISTA
Read_clear
Address 05H
5
4
3
2
1
0
D_XFR
XINT1
XINT0
D_EXI
B1_EXI
B2_EXI
相關PDF資料 |
PDF描述 |
|---|---|
| W6692A | TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
| W6692ACD | ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
| W6692ACF | ISDN LINE INTERFACE|BASIC|CMOS|QFP|100PIN|PLASTIC |
| W6694A | TE Mode S/T Controller with USB 1.1 Interface |
| W6694CD | USB Bus ISDN S/T-Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W66910CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:TE Mode ISDN S/T-Controller with Microprocessor Interface |
| W6691CD | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6691CP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISDN S/T Interface Transceiver |
| W6692 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCI Bus ISDN S/T-Controller |
| W6692A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TE Mode S/T Controller with PCI 2.2 Interface and ACPT |
發布緊急采購，3分鐘左右您將得到回復。