參數資料
型號： XCF128XFTG64C
廠商： Xilinx Inc
文件頁數： 29/88頁
文件大?。?/td> 0K
描述： IC PROM SRL 128M GATE 64-FTBGA
標準包裝： 1
可編程類型： 系統內可編程
存儲容量： 128Mb
電源電壓： 1.7 V ~ 2 V
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-TBGA
供應商設備封裝： 64-TFBGA
包裝： 托盤
產品目錄頁面： 601 (CN2011-ZH PDF)
其它名稱： 122-1578
Platform Flash XL High-Density Configuration and Storage Device
DS617 (v3.0.1) January 07, 2010
Product Specification
35
R
Block Locking
Platform Flash XL features an instant, individual block-locking
scheme, allowing any block to be locked or unlocked with no
latency. This locking scheme has three levels of protection:
Lock/Unlock – this first level allows software only
control of block locking.
Lock-Down – this second level requires hardware
interaction before locking can be changed.
VPP = VPPLK – this third level offers a complete hardware
protection against program and erase on all blocks.
The protection status of each block can be set to Locked,
Unlocked, and Locked-Down. Table 18, page 38, defines all of
the possible protection states (WP, DQ1, DQ0), and Figure 43,
page 77, shows a flowchart for the locking operations.
Reading a Block’s Lock Status
The lock status of every block can be read during the Read
Electronic Signature mode of the device (see "Read
Electronic Signature Command," page 14). Subsequent
reads at the address specified in Table 9, page 21 output
the protection status of that block.
The lock status is represented by DQ0 and DQ1. DQ0
indicates the Block Lock/Unlock status and is set by the
Lock command and cleared by the Unlock command. DQ0
is automatically set when entering Lock-Down. DQ1
indicates the Lock-Down status and is set by the Lock-Down
command. DQ1 cannot be cleared by software, only by a
hardware reset or power-down.
Block Lock States
Locked State
The default status of all blocks on power-up or after a
hardware reset is Locked (states (0,0,1) or (1,0,1)). Locked
blocks are fully protected from program or erase operations.
Any program or erase operations attempted on a locked
block returns an error in the Status Register. The status of a
locked block can be changed to Unlocked or Locked-Down
using the appropriate software commands. An unlocked
block can be Locked by issuing the Lock command.
Unlocked State
Unlocked blocks (states (0,0,0), (1,0,0) (1,1,0)) can be
programmed or erased. All unlocked blocks return to the
Locked state after a hardware reset or when the device is
powered-down.
The status of an unlocked block can be changed to Locked or
Locked-Down using the appropriate software commands. A
locked block can be unlocked by issuing the Unlock command.
Locked-Down State
Blocks that are Locked-Down (state (0,1,x)) are protected
from program and erase operations (similar to locked
blocks) but their protection status cannot be changed using
software commands alone. A locked or unlocked block can
be locked down by issuing the Lock-Down command.
Locked-down blocks revert to the Locked state when the
device is reset or powered-down.
The Lock-Down function is dependent on the Write Protect
(WP) input pin. When WP =0 (VIL), blocks in the Lock-
Down state (0,1,x) are protected from program, erase and
protection status changes.
When WP =1 (VIH), the Lock-Down function is disabled
(1,1,x), and locked-down blocks can be individually
unlocked to the (1,1,0) state by issuing the software
command to erase and programme.
When the Lock-Down function is disabled (WP =1), blocks
can be locked (1,1,1) and unlocked (1,1,0) as desired.
When WP = 0. Blocks previously locked-down return to the
Lock-Down state (0,1,x), regardless of any changes made
while WP =1.
Device reset or power-down resets all blocks, including
those in Locked-Down, to the Locked state.
Locking Operations during Erase Suspend
Changes to block lock status can be performed during a
suspended erase by using standard locking command
sequences to unlock, lock or lock-down a block. This
capability is useful in the case when another block needs to
be updated while an erase operation is in progress.
Three steps are needed to change block locking during an
erase operation:
1.
An Erase Suspend command is issued.
2.
The Status Register is checked until it indicates that the
erase operation is suspended.
3.
The desired Lock command sequence is issued to a
block (lock status changes).
After completing any desired lock, read, or program
operations, the erase operation is resumed with the Erase
Resume command.
If a block is locked or locked-down during a suspended
erase of the same block, the locking status bits are changed
immediately. But when the erase is resumed, the erase
operation completes. Locking operations cannot be
performed during a program suspend.
相關PDF資料
PDF描述
XCF32PFS48C IC PROM SRL 1.8V 32M 48CSBGA
XCR3256XL-7CS280C IC CPLD 256MCELL 3.3V HP 280CSP
XCS10-3VQG100C IC FPGA 5V C-TEMP 100-VQFP
XCV600E-8HQ240C IC FPGA 1.8V C-TEMP 240-HQFP
XCV812E-8FG900C IC FPGA 1.8V C-TEMP 900-FBGA
相關代理商/技術參數
參數描述
XCF128XFTG64CES 制造商:Xilinx 功能描述:
XCF12-L4Z1 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / XCF12-L4Z1
XCF12-S1 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / XCF12-S1
XCF13-S1 制造商:SAIA - BURGESS ELECTRONICS INC. 功能描述:Catalogue / XCF13-S1
XCF16P 制造商:XILINX 制造商全稱:XILINX 功能描述:Platform Flash In-System Programmable Configuration PROMs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*