- 您現在的位置：買賣IC網 > PDF目錄11834 > XR88C681P/40-F (Exar Corporation)IC UART CMOS DUAL 40PDIP PDF資料下載
參數資料
| 型號： | XR88C681P/40-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 64/101頁 |
| 文件大小： | 0K |
| 描述： | IC UART CMOS DUAL 40PDIP |
| 標準包裝： | 9 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 1 字節，3 字節 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 帶并行端口： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-PDIP |
| 包裝： | 管件 |
| 其它名稱： | 1016-1640 XR88C681P/40-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
XR88C681
65
Rev. 2.11
data, at the Data Bus, specifying the bits, within the OPR,
to be set ( 1 = set, 0 = no change). A bit is cleared by the
address triggered “CLEAR OUTPUT PORT BITS”
command (see
Table 1) with the accompanying data, at
the Data Bus, specifying the bits to be reset (1 = cleared, 0
= no change).
F.1 Writing Data to the OPR/Output Port Pins
As mentioned earlier, the state of the OPR and
consequently, the Output Port pins is controlled by two
“Address Triggered” commands.
D
Set Output Port Bits Command
D
Clear Output Port Bits Command
The procedure and effect of using these commands are
discussed in
Section F.1.1.
F.1.1 Set Ouput Port Bits Command
The actual procedure used to invoke the “SET OUTPUT
PORT BITS” command is the same as writing the
contents on the Data Bus (D7 - D0) to DUART Address
0E16 for (OP7 - OP0). For every “1” that exists within the
latched contents of the Data Bus, the corresponding bit,
within the OPR is set to a logic “high”. For every “0” that is
present on the data bus and is written to DUART Address
0E16, the state of the corresponding bit, within the OPR is
unchanged.
We could state this another way as: For every “1” that is
present on the Data Bus, during the use of the “SET
OUTPUT PORT BITS” command, the corresponding
Output Port pin is set to a logic “l(fā)ow”. And for every “0” that
is present on the Data Bus, during this command, the
state of the corresponding Output Port pin is unchanged.
For Example:
Suppose that the content of the OPR are OPR[7:0] = [0, 0,
0, 0, 1, 1, 1, 1]. Hence, the state of the Output Port pins
are as follows:
[OP7, OP6, OP5, OP4, OP3, OP2, OP1, OP0] = [1, 1, 1, 1,
0, 0, 0, 0]
If we write the following to DUART Address 0E16;
[D7,...,D0] = [1, 1, 1, 1, 0, 0, 0, 0]; the resulting state of the
Output Port Register Bits follows:
OPR[7:0] = [1, 1, 1, 1, 1, 1, 1, 1].
Consequently, the state of the Output Port pins are as
follows:
[OP7, OP6, OP5, OP4, OP3, OP2, OP1, OP0] = [0, 0, 0, 0,
0, 0, 0, 0]
This example of the “SET OUTPUT PORT BITS”
command is illustrated in
Figure 33.
State of Output Port Pins (OP7 - OP0)
Initial OPR[7:0]
Final OPR[7:0]
Data Bus, D7 - D0
Figure 33. Illustration of the “SET OUTPUT PORT BIT” Command and its Effect
on the Output Port Register and the State of the Output Port Pins.
DUART Address 0Eh
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| MS27472T16B8PA | CONN RCPT 8POS WALL MT W/PINS |
| MS27473E12F8PA | CONN PLUG 8POS STRAIGHT W/PINS |
| VI-JWH-IW-F3 | CONVERTER MOD DC/DC 52V 100W |
| VI-JWH-IW-F2 | CONVERTER MOD DC/DC 52V 100W |
| VI-JWH-IW-F1 | CONVERTER MOD DC/DC 52V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR88C681XR101524CNN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XR88C681XR101524M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XR88C681XR101524N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XR88C681XR101528CJJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XR88C681XR101528CNN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。