參數資料
型號： AM5X86
廠商： Advanced Micro Devices, Inc.
英文描述： High-Performance Design On-Chip Integration Complete 32-Bit Architecture Micrprocessor(高性能單片32位微處理器)
中文描述： 高性能設計的片上集成完整的32位架構Micrprocessor（高性能單片32位微處理器）
文件頁數： 16/67頁
文件大?。?/td> 1201K
代理商： AM5X86
16
Am5
X
86 Microprocessor
AMD
PRELIMINARY
LOCK
Bus Lock (Active Low; Output)
A Low output on this pin indicates that the current bus
cycle is locked. The microprocessor ignores HOLD
when LOCK is asserted (although it does acknowledge
AHOLD and BOFF). LOCK goes active in the first clock
of the first locked bus cycle and goes inactive after the
last clock of the last locked bus cycle. The last locked
cycle ends when RDY is returned. LOCK is active Low
and is not driven during bus hold. Locked read cycles
are not transformed into cache fill cycles if KEN is active.
M/IO
Memory/Input-Output (Active High/Active Low;
Output)
A High output indicates a memory cycle. A Low output
indicates an I/O cycle.
NMI
Non-Maskable Interrupt (Active High; Input)
A High NMI input signal indicates that an external non-
maskable interrupt has occurred. NMI is rising-edge
sensitive. NMI must be held Low for at least four CLK
periods before this rising edge. The NMI input does not
have an internal pull-down resistor. The NMI input is
asynchronous, but must meet setup and hold times t
20
and t
21
for recognition in any specific clock.
PCD
Page Cache Disable (Active High; Output)
This pin reflects the state of the PCD bit in the page
table entry or page directory entry (programmable
through the PCD bit in CR3). If paging is disabled, the
CPU ignores the PCD bit and drives the PCD output
Low. PCD has the same timing as the cycle definition
pins (M/IO, D/C, and W/R). PCD is active High and is
not driven during bus hold. PCD is masked by the Cache
Disable bit (CD) in Control Register 0 (CR0).
PCHK
Parity Status (Active Low; Output)
Parity status is driven on the PCHK pin the clock after
RDY for read operations. The parity status reflects data
sampled at the end of the previous clock. A Low PCHK
indicates a parity error. Parity status is checked only for
enabled bytes as is indicated by the byte enable and
bus size signals. PCHK is valid only in the clock imme-
diately after read data is returned to the microprocessor;
at all other times PCHK is inactive High. PCHK is floated
only during Tri-state Test mode (see FLUSH).
PLOCK
Pseudo-Lock (Active Low; Output)
In Write-back mode, the processor forces the output
High and the signal is always read as inactive. In Write-
through mode, PLOCK operates normally. When
asserted, PLOCK indicates that the current bus
transaction requires more than one bus cycle. Examples
of such operations are segment table descriptor reads
(8 bytes) and cache line fills (16 bytes). The micropro-
cessor drives PLOCK active until the addresses for the
last bus cycle of the transaction have been driven,
whether or not RDY or BRDY is returned. PLOCK is a
function of the BS8, BS16, and KEN inputs. PLOCK
should be sampled on the clock when RDY is returned.
PLOCK is active Low and is not driven during bus hold.
PWT
Page Write-Through (Active High; Output)
This pin reflects the state of the PWT bit in the page
table entry or page directory entry (programmable
through the PWT bit in CR3). If paging is disabled, the
CPU ignores the PWT bit and drives the PWT output
Low. PWT has the same timing as the cycle definition
pins (M/IO, D/C, and W/R). PWT is active High and is
not driven during bus hold.
RESET
Reset (Active High; Input)
RESET forces the microprocessor to initialize. The mi-
croprocessor cannot begin execution of instructions un-
til at least 1 ms after V
CC
and CLK have reached their
proper DC and AC specifications. To ensure proper mi-
croprocessor operation, the RESET pin should remain
active during this time. RESET is active High. RESET
is asynchronous but must meet setup and hold times
t
20
and t
21
to ensure recognition on any specific clock.
RDY
Non-Burst Ready (Active Low; Input)
A Low input on this pin indicates that the current bus
cycle is complete, that is, either the external system has
presented valid data on the data pins in response to a
read, or the external system has accepted data from the
microprocessor in response to a write. RDY is ignored
when the bus is idle and at the end of the bus cycle’s
first clock. RDY is active during address hold. Data can
be returned to the processor while AHOLD is active.
RDY is active Low and does not have an internal pull-
up resistor. RDY must satisfy setup and hold times t
16
and t
17
for proper chip operation.
SMI
SMM Interrupt (Active Low; Input)
A Low signal on the SMI pin signals the processor to
enter System Management mode (SMM). SMI is the
highest level processor interrupt. The SMI signal is rec-
ognized on an instruction boundary, similar to the NMI
and INTR signals. SMI is sampled on every rising clock
edge. SMI is a falling-edge sensitive input. The SMI input
has an internal pull-up resister. Recognition of SMI is
guaranteed in a specific clock if it is asserted synchro-
nously and meets the setup and hold times. If SMI is
asserted asynchronously, it must go High for a minimum
of two clocks before going Low, and it must remain Low
相關PDF資料
PDF描述
AM6TW-2424D 6 watt dc-dc converters
AM6TW-4803SH35 6 watt dc-dc converters
AM6TW-4805D 6 watt dc-dc converters
AM6TW-4805DH35 6 watt dc-dc converters
AM6TW-4805S 6 watt dc-dc converters
相關代理商/技術參數
參數描述
AM5X86-P75 制造商:Advanced Micro Devices 功能描述:Microprocessor, 32 Bit, 168 Pin, Ceramic, PGA
AM6 功能描述:按鈕開關 Push Button Oper, 30 mm,Non Ill. Mush., Mom., Blue RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
AM-6 制造商:Greenlee Textron Inc 功能描述:MULTIMETER ANALOG 制造商:Greenlee Textron Inc 功能描述:MULTIMETER,ANALOG
AM60 制造商:Thomas & Betts 功能描述:60A ANGLE ADAPTER
AM600 制造商:EXTECH 制造商全稱:Extech Instruments Corporation. 功能描述:600A AC Analog Clamp Meter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*