- 您現在的位置：買賣IC網 > PDF目錄16900 > APMOTOR56F8000E (Freescale Semiconductor)KIT DEMO MOTOR CTRL SYSTEM PDF資料下載
參數資料
| 型號： | APMOTOR56F8000E |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 101/124頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT DEMO MOTOR CTRL SYSTEM |
| 標準包裝： | 1 |
| 附件類型： | 電機控制器 |
| 適用于相關產品： | DEMO56F8013，DEMO56F8013-E |
| 相關產品： | MC56F8006VWL-ND - DSC 16K FLASH 32MHZ 28-SOIC MC56F8006VLF-ND - DSC 16K FLASH 32MHZ 48-LQFP MC56F8006VLC-ND - DSC 16K FLASH 32MHZ 32-LQFP MC56F8002VWL-ND - DSC 12K FLASH 32MHZ 28-SOIC DEMO56F8014-E-ND - BOARD DEMO MC56F8014 W/UNIV PS DEMO56F8014-ND - BOARD DEMO MC56F8014 W/US PS DEMO56F8014-EE-ND - BOARD DEMO FOR 56F8014 DEMO56F8013-EE-ND - BOARD DEMO FOR 56F8013 MC56F8014VFAE-ND - IC DIGITAL SIGNAL CTRLR 32-LQFP MC56F8013VFAE-ND - IC DIGITAL SIGNAL CTLR 32-LQFP 更多... |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁當前第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
56F8014 Technical Data, Rev. 11
78
Freescale Semiconductor
The power modes provide additional means to disable clock domains, configure the voltage regulator, and
configure clock generation to manage power utilization, as shown in Table 6-3. Run, Wait, and Stop
modes provide means of enabling/disabling the peripheral and/or core clocking as a group. Stop disable
controls are provided for selected peripherals in the control register so that these peripheral clocks can
optionally continue to operate in Stop mode and generate interrupts which will return the part from Stop
to Run mode. Standby mode provides normal operation but at very low speed and power utilization. It is
possible to invoke Stop or Wait mode while in Standby mode for even greater levels of power reduction.
A 200 kHz clock external clock can optionally be used in Standby mode to produce the required Standby
100 kHz system bus rate. Power-down mode, which selects the ROSC clock source but shuts it off, fully
disables the part and minimizes its power utilization but is only recoverable via reset.
When the PLL is not selected and the system bus is operating at around 100 kHz, the large regulator can
Wait
Core and memory
clocks disabled
Peripheral clocks
enabled
Core executes WAIT instruction to enter this
mode.
Typically used for power-conscious applications.
Possible recoveries from Wait mode to Run
mode are:
1. Any interrupt
2. Executing a Debug mode entry command
during the 56800E core JTAG interface
2. Any reset (POR, external, software, COP)
Stop
Master clock generation in the OCCS
remains operational, but the SIM disables
the generation of system and peripheral
clocks.
Core executes STOP instruction to enter this
mode. Possible recoveries from Stop mode to
Run mode are:
1. Interrupt from Timer channels that have been
configured to operate in Stop mode (TCx_SD)
2. Interrupt for SCI configured to operate in Stop
mode (SCI_SD)
3. Low-voltage interrupt
4. Executing a Debug mode entry command
using the 56800E core JTAG interface
5. Any reset (POR, external, software, COP)
Standby
The OCCS generates the 2x System Clock
at a reduced frequency (200 kHz). The PLL
and high speed peripheral clocks are
disabled and the high-speed peripheral
option is not available. System and
peripheral clocks operate at 100 kHz.
The user configures the OCCS and SIM to select
the relaxation oscillator clock source (PRECS),
shut down the PLL (PLLPD), put the relaxation
oscillator in Standby mode (ROSB), and put the
large regulator in Standby (LRSTDBY). The part
is fully operational, but operating at a minimum
frequency and power configuration. Recovery
requires reversing the sequence used to enter
this mode (allowing for PLL lock time).
Power-Down
Master clock generation in the OCCS is
completely shut down. All system and
peripheral clocks are disabled.
The user configures the OCCS and SIM to enter
Standby mode as shown in the previous
description, followed by powering down the
oscillator (ROPD). The only possible recoveries
from this mode are:
1. External reset
2. Power-on reset
Table 6-3 Clock Operation in Power-Down Modes (Continued)
Mode
Core Clocks
Peripheral Clocks
Description
相關PDF資料 |
PDF描述 |
|---|---|
| TCMD-05-S-06.00-01 | CABLE ASSEM 2MM 10POS SGL END 6" |
| 8532-09L | INDUCTOR 4.7UH POWER SMD |
| LM4040BEX3-5.0+T | IC VREF SHUNT PREC 5V SC-70-3 |
| GBC13DRAN-S734 | CONN EDGECARD 26POS .100 R/A SLD |
| LM4040BEX3-2.5+T | IC VREF SHUNT PREC 2.5V SC-70-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APMP100 | 功能描述:CHEMICAL METERING PUMP. 制造商:3m 系列:* 零件狀態:在售 標準包裝:1 |
| AP-MP3 | 制造商:Rogue Robotics 功能描述:uMP3 Playback Module 3-5 Volt MP3 PCM WAV Interface with PIC |
| APMR0016 | 功能描述:MOD APMR 3-PH VAULT DET DIN RAIL RoHS:否 類別:工業控制，儀表 >> 專用 系列:APMR 標準包裝:1 系列:PSE200 產品目錄頁面:2804 (CN2011-ZH PDF) 其它名稱:606-1016 |
| APMR0086 | 制造商:Red Lion Controls 功能描述:SIGNAL CONDIT MOD, 3 PH FAULT DET 380V 制造商:Red Lion Controls 功能描述:3 PHASE FAULT DETECTOR 380VAC |
| APMR0096 | 制造商:Red Lion Controls 功能描述:Relay, Analog Phase Mod, 480 制造商:Red Lion Controls 功能描述:3 PHASE FAULT DETECTOR 480VAC |
發布緊急采購，3分鐘左右您將得到回復。